UA379A-E HESG332084R1 HE665727-318/6 速度传感器模块

UA379A-E HESG332084R1 HE665727-318/6 速度传感器模块 

通过将以太网电缆的另一端连接到快速以太网
标准以太网组件。请参阅PTUST04-3211-交换机管理
适用于IEC 61850，适用于经IEC 61850认证的开关。
安装AF 100接口CI869
CI869单元由处理器单元通过CEX总线供电，无
需要额外的外部电源。
要安装CI869：
1.将CI869装置安装到DIN导轨上。参见将AC 800M装置安装到
DIN导轨，第65页。
2.将AF 100双绞线连接至CI869的4针触点。
如果是冗余介质，将另一个AF 100双绞线连接到另一个
4针触点。
3.将双绞线的另一端连接到AF 100总线。
有关AF 100连接的详细信息，请参阅Advant现场总线100用户手册
（3BSE000506*）。
第2节安装：安装PROFINET IO接口CI871
3BSE036351-510 A 129
安装PROFINET IO接口CI871
CI871单元由处理器单元通过CEX总线供电，其中
不需要额外的外部电源。
要安装CI871：
1.将CI871装置安装在DIN导轨上。
2.将100 Mbps以太网电缆连接至基板上的CH1连接器。
3.将以太网电缆的另一端连接到PROFINET IO网络。
安装MOD5接口CI872
CI872单元由处理器单元通过CEX总线供电，并且
不需要任何额外的外部电源。
要安装CI872：
1.将装置安装到DIN导轨上。
2.将光纤电缆连接到上的CH1、CH2和CH3连接器
CI872.将保护插头安装在未使用的端口上。
3.将光纤电缆的另一端连接至MOD5控制器。
光纤规范
以下数据适用于AC 800M之间的光纤连接
控制器和MOD5控制器：
•波长：820nm。
•纤维尺寸：62.5/125米多模玻璃纤维。
•连接器类型：ST。
•包括连接器在内的大标称光纤阻尼：11 dB。

安装以太网/IP接口CI873第2节安装
130 3BSE036351-510 A
安装以太网/IP接口CI873
CI873由处理器单元通过CEX总线供电，这需要
没有额外的外部电源。
按照以下步骤安装CI873：
1.将装置安装到DIN导轨上。
2.将100 Mbps以太网双绞线连接到
底板。
3.将以太网电缆的另一端连接到快速以太网网络
通过标准以太网组件。

UA379A-E HESG332084R1 HE665727-318/6 速度传感器模块 

UA379A-E HESG332084R1 HE665727-318/6 速度传感器模块 

Connect the other end of the Ethernet cable to a Fast Ethernet network via
standard Ethernet components. Refer to PTUST04-3211- Switch Management
for IEC 61850 for switches that are certified for IEC 61850.
Installing the AF 100 Interface CI869
The CI869 unit is powered from the processor unit via the CEX-Bus with no
additional external power source required.
To install CI869:
1. Mount the CI869 unit onto the DIN-rail. See Mounting AC 800M Units onto
DIN-Rail on page 65.
2. Connect the AF 100 twisted pair to the 4-pin contact of CI869.
In case of redundant media, connect the other AF 100 twisted pair to the other
4-pin contact.
3. Connect the other end of the twisted pair to the AF 100 bus.
For details on AF 100 connections, refer to the Advant Fieldbus 100 User Manual
(3BSE000506*).
Section 2 Installation Installing the PROFINET IO Interface CI871
3BSE036351-510 A 129
Installing the PROFINET IO Interface CI871
The CI871 unit is powered from the processor unit through the CEX-Bus, which
requires no additional external power source.
To install CI871:
1. Mount the CI871 unit on the DIN-rail.
2. Connect the 100 Mbps Ethernet cable to the CH1 connector on the baseplate.
3. Connect the other end of the Ethernet cable to the PROFINET IO network.
Installing the MOD5 Interface CI872
The CI872 unit is powered from the processor unit through the CEX-bus, and does
not require any additional external power source.
To install CI872:
1. Mount the unit onto the DIN-rail.
2. Connect the fiber optic cables to the CH1, CH2, and CH3 connectors on the
CI872. Leave the protective plugs mounted on unused ports.
3. Connect the other end of the fiber optic cable to a MOD5 controller.
Fiber Optics Specifications
The following data applies for the fiber optics connections between the AC 800M
controller and MOD5 controllers:
• Wavelength: 820 nm.
• Fiber size: 62.5/125 m multimode glass fiber.
• Connector type: ST.
• Max nominal fiber damping including connectors: 11 dB.

Installing the EtherNet/IP Interface CI873 Section 2 Installation
130 3BSE036351-510 A
Installing the EtherNet/IP Interface CI873
The CI873 is powered from the processor unit through the CEX-Bus, which requires
no additional external power source.
Follow the steps below to install CI873:
1. Mount the unit onto the DIN-rail.
2. Connect the 100 Mbps Ethernet twisted pair cable to the CH1 connector on the
baseplate.
3. Connect the other end of the Ethernet cable to the Fast Ethernet network
through the standard Ethernet components.