XVC770BE101 3BHE021083R0101 输入输出通讯主板 ABB
本章包含调试卷筒纸张力系统所需的信息。
假设腹板张力系统已按照给出的说明安装
在2章安装和附录（B、C、D、E、F或G）中，取决于已安装的称重传感器
类型
开始调试前，您必须具备以下数据：
1.称重传感器类型和标称荷载，安装的称重传感器类型见附录
2.系统定义见3.12.2节。
•称重传感器组合
–一卷（称重传感器A和B）
–两个辊（辊1连接到A和B，辊2连接到C和D）或
-分段卷
•增益调度（为两个不同的web路径切换包裹增益）。
–一卷、两卷（仅卷1）和分段卷。
3.对象类型，见3.12.3节。
•标准辊（辊1、称重传感器A和B或辊2、称重传感器C和D）
•单侧测量（辊1、称重传感器A或B和辊2、称重传感器C或D）
•分段卷
多可处理连接到三个PFEA113的12个称重传感器。称重传感器输入
必须连接到PFEA113，如下所示：
-一个输入，称重传感器连接到
-两个输入，称重传感器连接到A和B
-三个输入，称重传感器连接到A、B和C
-四个输入，称重传感器连接到A、B、C和D
4.给定卷筒纸张力下的期望输出数据
5.通信数据，见3.13节。
3.2安全说明
在开始任何操作之前，请阅读并遵循1章介绍中所述的安全说明
调试工作。然而，如果当地法规更严格，则应优先考虑。
3.3必要的设备和文件
需要以下项目：
•电缆图
•服务工具
张力电子PFEA113，用户手册
三章调试
3-2 3 BSE029382R0101版本C
3.4使用面板按钮
3.4.1导航和确认
3.4.2改变数值和参数
•X表示数值。
•Z表示可以从列表中选择参数。
要更改数值X或参数Z，请按。数值或参数为
然后放在方括号[XXXXXX]或[ZZ]内，表示可以更改。
如果是“Z”参数，请使用和在列表中上移或下移。当所需值
显示按钮上显示。按下时，将保存新参数值，并
值周围的括号消失。
如果您已按下，使参数被括号括起来，则可以取消
按进入模式。使用和进行的选择将不会被存储。如果
按下时，旧值不带括号显示。
若要更改数值，请按，使值周围出现括号。那么一个
数字可以使用和进行更改。当一个数字具有所需值时，按，然后
二个数字可以使用和进行更改。在后一个数字后按
设置后，新值将保存并显示，不带括号。
输入数值时使用表示返回上一个数字。按
足够的次数后，您将离开进入模式，旧值将为
无支架显示
XVC770BE101 3BHE021083R0101 输入输出通讯主板 ABB
XVC770BE101 3BHE021083R0101 输入输出通讯主板 ABB
This chapter contains the information needed to commission a Web Tension System.
It is assumed that the Web Tension System has been installed according to the instructions given
in Chapter 2 Installation and Appendix (B, C, D, E, F or G) depending on installed load cell
type.
You must have the following data before starting commissioning:
1. Load cell type and nominal load, see Appendix for installed load cell type
2. System definition, see Section 3.12.2.
• Load cell combination
– One roll (load cells A and B)
– Two rolls (Roll 1 connected to A and B, Roll 2 connected to C and D) or
– Segmented roll
• Gain scheduling (switching wrap gain for two different web paths).
– One roll, Two rolls (only Roll 1) and Segmented roll.
3. Object type, see Section 3.12.3.
• Standard roll (Roll 1, load cells A and B or Roll 2, load cells C and D)
• Single side measurement (Roll 1, load cell A or B and Roll 2, load cell C or D)
• Segmented roll
Up to 12 load cells connected to max. three PFEA113 can be handled. The load cell inputs
must be connected to PFEA113 as follows:
- One input, load cell connected to A
- Two inputs, load cells connected to A and B
- Three inputs, load cells connected to A, B and C
- Four inputs, load cells connected to A, B, C and D
4. Desired output data at given web tension
5. Communication data, see Section 3.13.
3.2 Safety Instructions
Read and follow the safety instructions described in Chapter 1 Introduction, before starting any
commissioning work. However, local statutory regulations, if stricter, are to take precedence.
3.3 Necessary Equipment and Documentation
The following items are required:
• Cable diagram
• Service tools
Tension Electronics PFEA113, User Manual
Chapter 3 Commissioning
3-2 3BSE029382R0101 Rev C
3.4 Using the Panel Buttons
3.4.1 Navigating and Confirming
3.4.2 Changing Numerical Values and Parameters
• X indicates a numerical value.
• Z indicates that a parameter can be chosen from a list.
To change a numerical value, X, or parameter, Z, press . The numerical value or parameter is
then placed within brackets [XXXXXX] or [ZZ] to show that it can be changed.
If it is a “Z” parameter, use and to move up or down in the list. When the desired value
is shown on the display press . When is pressed the new parameter value is saved and
the brackets around the value disappear.
If you have pressed so that the parameter is enclosed by brackets, you can cancel the
entering mode by pressing . The selections made with and will not be stored. If
is pressed the old value is displayed without brackets.
To change a numerical value, press so that brackets appear around the value. Then the first
digit can be changed with and . When the first digit has the desired value press , then
the second digit can be changed with and . When pressing after the last digit has
been set, the new value is saved and displayed without brackets.
Using when entering a numerical value means returning to the previous digit. By pressing
a sufficient number of times you will leave the entering mode and the old value will be
displayed without bracke
XVC770BE101 3BHE021083R0101 输入输出通讯主板 ABB
