500SCM01 1MRB150004R0001 连接器模块全新 ABB
n调度允许在一个测量辊上使用两个不同的卷筒纸路径。可以设置缠绕增益的两个预定义值。
包角增益1用于包角1，包角增益2用于包角2。
通过数字输入信号或通路选择要使用的两个包络增益中的哪一个
Profibus。
对于称重传感器组合，双辊增益调度仅适用于辊1。
如果数字输入设置为“0”，或者如果指定的字段
Profibus设置为“0”。
如果数字输入设置为“1”，或者如果指定的字段
Profibus设置为“1”。
如果数字输入用于缠绕增益调度，Profibus中的缠绕增益调度字段为：
残废
如果数字输入用于远程零点设置或设置为“关闭”，则控制回绕增益调度
来自Profibus。
快速安装
网张力
演示文稿-菜单
设定标称负载
服务菜单
零集
SetWrapGain
>5秒
AO 1-AO 6
混杂的
菜单
系统定义
对象类型
做1-做4
AI 1-AI 2
迪
包角1
张力电子PFEA113，用户手册
第3.12.3节设置对象类型
3BSE029382R0101版本C 3-17
3.12.3设置对象类型
根据称重传感器组合，称重传感器梳：
•一卷
•两卷或
•分段卷
在菜单“系统定义”中选择以下对象类型。
图3-5.设置一卷的对象类型
使用上下键从列表中选择对象类型[ZZ]。
1.标准辊（两个称重传感器，A和B连接）
2.单侧A（仅连接称重传感器A）
3.单侧B（仅连接称重传感器B）
选择单侧测量时，测量信号乘以2并
在显示器和模拟输出上显示为卷筒纸张力。
3.12.3.1一卷的对象类型
图3-6.一卷的对象类型
快速安装
网张力
展示菜单
设定标称负载
服务菜单
泽罗
单侧B测量
张力电子PFEA113，用户手册
第三章调试
3-18 3 BSE029382R0101版本C
3.12.3.2设置两辊的对象类型
使用上下键从列表中选择对象类型[ZZ]。
卷1：标准卷（称重传感器A和B）、单侧A或单侧B（称重传感器B或A）
卷2：标准卷（称重传感器C和D）、单面C或单面（称重传感器B或D）
选择单侧测量时，测量信号乘以2并
在显示器和模拟输出上显示为卷筒纸张力。
图3-7两卷的对象类型
滚动1设置对象
ZZ
设置对象
ZZ
你确定吗
[ZZ]
你确定吗
[ZZ]
设置两卷的对象类型
第二卷
对象类型
张力电子PFEA113，用户手册
第3.12.3节设置对象类型
3BSE029382R0101版本C 3-19
3.12.3.3设置分段辊的对象类型
对象类型SegmentedRoll多可用于连接到一个、两个或多个传感器的12个称重传感器
三个张力电子元件PFEA113。
每个PFEA113必须设置为：
•一个输入（称重传感器连接到A）
•两个输入（称重传感器连接到A和B）
•三个输入（连接到A、B和C的称重传感器）或
•四个输入（连接到A、B、C和D的称重传感器）
图3-8.设置分段辊的对象类型
使用上下键从列表中选择对象类型[ZZ]。
•OneInput
•两个输入
•三输入或
•四个输入
分段轧辊比例系数（SRSF）用于补偿总测量张力，以及
当不是所有轧辊都由分段式称重传感器支撑时，给出总张力的估计值
滚动应用程序。有关SRSF的计算，请参考附录A.3.1分段辊秤
因子（SRSF）。
图3-9.连接到一个PFEA113的分段辊
快速安装
网张力
展示菜单
设定标称负载
服务菜单
零集
SetWrapGain
>5秒
AO 1-AO 6
混杂的
菜单
系统定义
对象类型
做1-做4
AI 1-AI 2
迪
设置对象
ZZ
你确定要设置对象吗
[ZZ]至
对象类型
设置分段辊的对象类型
设定标称负载
A.
500SCM01 1MRB150004R0001 连接器模块全新 ABB
500SCM01 1MRB150004R0001 连接器模块全新 ABB
n scheduling enables the use of two different web paths on one measuring roll. Two predefined values for wrap gain can be set.
Wrap gain 1 is used for wrap angle 1 and wrap gain 2 for wrap angle 2.
Which of the two wrap gains that is to be used is selected with a digital input signal or via
Profibus.
For load cell combination TwoRolls gain scheduling is available only for Roll 1.
Wrap gain parameter 1 is used if the digital input is set to “0”, or if the specified field in
Profibus is set to “0”.
Wrap gain parameter 2 is used if the digital input is set to “1”, or if the specified field in
Profibus is set to “1”.
If the digital input is used for wrap gain scheduling the wrap gain scheduling field in Profibus is
disabled.
If the digital input is used for remote zero set or set to “Off”, wrap gain scheduling is controlled
from Profibus.
FastSetUp
WebTension
Presentation- Menu
SetNominalLoad
ServiceMenu
ZeroSet
SetWrapGain
> 5 s
AO 1 - AO 6
Miscellaneous
Menu
SystemDefinition
ObjectType
DO 1 - DO 4
AI 1 - AI 2
DI
Wrap angle 1
Tension Electronics PFEA113, User Manual
Section 3.12.3 Setting Object Type
3BSE029382R0101 Rev C 3-17
3.12.3 Setting Object Type
Depending on which load cell combination, LoadCellComb:
• one roll
• two rolls or
• segmented roll
that is selected in menu “SystemDefinition” the following object types are available.
Figure 3-5. Setting Object Type for One Roll
Use up and down keys to select type of object [ZZ] from list.
1. StandardRoll (two load cells, A and B connected)
2. SingleSideA (only load cell A connected)
3. SingleSideB (only load cell B connected)
When single side measurement is selected the measured signal is multiplied by two and
presented as web tension on display and analog output.
3.12.3.1 Object Types for One Roll
Figure 3-6. Object Types for One Roll
FastSetUp
WebTension
PresentationMenu
SetNominalLoad
ServiceMenu
Zerroll
Single side B measurement
Tension Electronics PFEA113, User Manual
Chapter 3 Commissioning
3-18 3BSE029382R0101 Rev C
3.12.3.2 Setting Object Types for Two Rolls
Use up and down keys to select type of object [ZZ] from list.
Roll 1: StandardRoll (load cells A and B), SingleSideA or SingleSideB (load cell A or B)
Roll 2: StandardRoll (load cells C and D), SingleSideC or SingleSideD (load cell C or D)
When single side measurement is selected the measured signal is multiplied by two and
presented as web tension on display and analog output.
Figure 3-7. Object Types for Two Rolls
Roll 1 SetObject
ZZ
SetObject
ZZ
AreYouSure
[ZZ]
AreYouSure
[ZZ]
Setting Object Types for Two Rolls
Roll 2
ObjectTyp
Tension Electronics PFEA113, User Manual
Section 3.12.3 Setting Object Type
3BSE029382R0101 Rev C 3-19
3.12.3.3 Setting Object Types for Segmented Roll
Object type SegmentedRoll can be used for up to 12 load cells that are connected to one, two or
three Tension Electronics PFEA113.
Each PFEA113 must be set up for:
• one input (load cell connected to A)
• two inputs (load cells connected to A and B)
• three inputs (load cells connected to A, B and C) or
• four inputs (load cells connected to A, B, C and D)
Figure 3-8. Setting Object Types for Segmented Roll
Use up and down keys to select type of object [ZZ] from list.
• OneInput
• TwoInputs
• ThreeInputs or
• FourInputs
Segmented Roll Scale Factor (SRSF) is used to compensate the total measured tension and
present an estimate of total tension when not all rolls are supported by load cells in a segmented
roll application. For calculations of SRSF, refer to. Appendix A.3.1 Segmented Roll Scale
Factor (SRSF).
Figure 3-9. Segmented Roll Connected to One PFEA113
FastSetUp
WebTension
PresentationMenu
SetNominalLoad
ServiceMenu
ZeroSet
SetWrapGain
> 5 s
AO 1 - AO 6
Miscellaneous
Menu
SystemDefinition
ObjectType
DO 1 - DO 4
AI 1 - AI 2
DI
SetObject
ZZ
AreYouSure SetObject
[ZZ] To
ObjectType
Setting Object Types for Segmented Roll
SetNominalLoad
A
500SCM01 1MRB150004R0001 连接器模块全新 ABB
