UFC921A UFC921/A 3BHE024855R0102 工业PCB卡 ABB
ews。
4.将上转接板安装到称重传感器上，拧紧至表F-1中规定的扭矩，或
表F-2，并应用锁定液。
5.将轴承箱和辊安装到上转接板上，但不要完全拧紧
螺钉。
6.调整称重传感器，使其相互平行并与轴向一致
辊的方向。拧紧地脚螺钉。
7.调整辊，使其与称重传感器的纵向成直角。
拧紧上部适配器板中的螺钉。
8.对任何不防锈的机加工表面进行防锈保护。
张力电子PFEA113，用户手册
第F.7.2节安装
3BSE029382R0101版本C F-9
图F-3.典型安装
表F-1.符合ISO 898/1的MoS2润滑镀锌螺钉
强度等级尺寸拧紧力矩
8.8（1）（12.9）M16 170（286）纳米
表F-2.符合ISO 3506的不锈钢打蜡螺钉
强度等级尺寸拧紧力矩
A2-80（1）
（1） 当50 kN测力传感器较大时，建议其强度等级为12.9
预计会过载，尤其是如果固定螺钉受到
紧张
M16 187纳米
压力导管
系统
鲁尔
Övre mellanläggsplatta
Lastcell
梅兰拉塔
拉格胡斯
基础
上转接板
下转接板
卷
轴承箱
称重传感器
地基
张力电子PFEA113，用户手册
附录F PFCL 201-称重传感器安装设计
F-10 3BSE029382R0101 C版
F、 7.3称重传感器PFCL 201CE的布线
应安装带保护软管的电缆，以便中间部分的移动
不会阻止称重传感器。图F-4显示了如何使用电缆和保护软管
安装用于称重传感器PFCL 201CE。如果称重传感器的中间部分在其
移动时，它将分流力，测得的力将与实际力不同。
通过拧下接头，可以改变电缆和保护软管的方向
并将其旋转90-180°。确保接线盒和负载之间的电缆
重新安装接线盒时，电池不会卡住或损坏。
图F-4.PFCL 201CE允许的带保护软管的电缆敷设
注意！
安装带保护软管的电缆时，不得使其靠近接头弯曲
框，见图F-5，或垂直定向。
图F-5 PFCL 201CE不允许使用保护软管敷设电缆
带保护软管的接线盒电缆
运动方向
中间部分
笔记连接处不允许弯曲。
张力电子PFEA113，用户手册
第F.8节称重传感器PFCL 201的技术数据
3BSE029382R0101版本C F-11
F、 8技术数据称重传感器PFCL 201
表F-3.技术数据
PFCL 201型机组
标称负载1）
测量方向的标称载荷，Fnom
材料：不锈钢SIS 2387 DIN X4CrNiMo 165
UFC921A UFC921/A 3BHE024855R0102 工业PCB卡 ABB
UFC921A UFC921/A 3BHE024855R0102 工业PCB卡 ABB
ews.
4. Fit the upper adapter plate to the load cell, tighten to the torque stated in Table F-1 or
Table F-2, and apply locking fluid.
5. Fit the bearing housing and the roll to the upper adapter plate, but do not fully tighten the
screws.
6. Adjust the load cells so that they are in parallel with each other and in line with the axial
direction of the roll. Tighten the foundation screws.
7. Adjust the roll so that it is at right angles to the longitudinal direction of the load cells.
Tighten the screws in the upper adapter plate.
8. Apply rust protection to any machined surfaces that are not rust proof.
Tension Electronics PFEA113, User Manual
Section F.7.2 Mounting
3BSE029382R0101 Rev C F-9
Figure F-3. Typical Installation
Table F-1. MoS2 lubricated , galvanized Screws According to ISO 898/1
Strength class Dimension Tightening torque
8.8 (1) (12.9) M16 170 (286) Nm
Table F-2. Waxed Screws of Stainless Steel According to ISO 3506
Strength class Dimension Tightening torque
A2-80 (1)
(1) Strength class 12.9 is recommended for 50 kN load cells, when large
overloads are expected, especially if the fixing screws are subjected to
tension.
M16 187 Nm
Pressductor
System
Rulle
Övre mellanläggsplatta
Lastcell
Undre mellanläggsplatta
Lagerhus
Fundament
Upper adapter plate
Lower adapter plate
Roll
Bearing housing
Load cell
Foundation
Tension Electronics PFEA113, User Manual
Appendix F PFCL 201 - Designing the Load Cell Installation
F-10 3BSE029382R0101 Rev C
F.7.3 Cabling for Load Cell PFCL 201CE
Cable with protective hose shall be mounted so that the movement of the intermediate part of
the load cell is not prevented. Figure F-4 shows how the cable and protective hose shall be
mounted for load cell PFCL 201CE. If the intermediate part of the load cell is prevented in its
movement, it will shunt force and the measured force will differ from the actual.
The direction of the cable and protecting hose can be changed by unscrewing the connection
box and turning it 90- 180°. Make sure that the cable between the connection box and the load
cell does not get jammed or damaged when the connection box is remounted.
Figure F-4. Allowed Laying of Cable with Protective Hose for PFCL 201CE
NOTE!
The cable with the protective hose must not be mounted so that it bends close to the connection
box, see Figure F-5, or is vertically directed.
Figure F-5. Not Allowed Laying of Cable with Protective Hose for PFCL 201CE
Connection box Cable with protective hose
Movement direction of
the intermediate part
Note! Bending is not allowed in the connection.
Tension Electronics PFEA113, User Manual
Section F.8 Technical Data Load Cell PFCL 201
3BSE029382R0101 Rev C F-11
F.8 Technical Data Load Cell PFCL 201
Table F-3. Technical Data
Type PFCL 201 Unit
Nominal loads 1)
Nominal load in measuring direction, Fnom
Material Stainless steel SIS 2387 DIN X4CrNiMo 165
UFC921A UFC921/A 3BHE024855R0102 工业PCB卡 ABB
