本手册
应用手册包含应用说明和设置指南
按函数排序。本手册可用于确定何时以及目的
可以使用典型的保护功能。本手册也可用于以下情况：
计算设置。
1.2预期受众
本手册针对负责以下工作的保护和控制工程师：
规划、预工程和工程。
保护和控制工程师必须具有电力方面的经验
工程和相关技术知识，如保护方案
以及原则。
1.3产品文档
1.3.1产品文档集
应用手册包含应用说明和设置指南
按函数排序。本手册可用于确定何时以及目的
可以使用典型的保护功能。本手册也可用于以下情况：
计算设置。
通信协议手册描述了通信协议
由IED支持。本手册侧重于供应商特定的实施。
工程指南提供了615的IEC 61850工程信息
带PCM600和IET600的系列保护IED。本指南集中介绍
特别是关于GOOSE与这些工具通信的配置。这个
指南可在工程设计阶段用作技术参考，
安装和调试阶段以及正常服务期间。更多详情
关于工具使用，请参阅PCM600文档。
工程手册包含了如何使用以下方法对IED进行工程设计的说明：
PCM600中的不同工具。本手册提供了如何设置
PCM600项目，并在项目结构中插入IED。手册也
1MRS756378 K节
介绍
参考文献615
应用手册
推荐保护和控制功能工程的顺序，LHMI
IEC 61850和其他标准的功能和通信工程
支持的协议。
安装手册包含如何安装IED的说明。这个
本手册提供了机械和电气安装程序。章节
按安装IED的时间顺序组织。
操作手册包含了IED安装后如何操作的说明
已委托。本手册提供了监控和控制说明
以及设置IED。本手册还描述了如何识别干扰和
如何查看计算和测量的电网数据以确定
过错
点列表手册描述了数据点的外观和属性
特定于IED。本手册应与
相应的通信协议手册。
技术手册包含应用程序和功能说明和列表
功能块、逻辑图、输入和输出信号、设置参数和
技术数据按功能分类。本手册可作为技术参考
在工程设计阶段、安装和调试阶段，以及
正常服务。
1.3.2文件修订历史
文件修订/日期产品版本历史记录
A/2007-12-20 1.0发布
B/2008-02-08 1.0更新内容
C/2008-07-02 1.1更新内容以符合
产品版本
D/2009-03-04 2.0更新内容以符合
产品版本
E/2009-07-03 2.0更新内容
F/2010-06-11 3.0更新内容以符合
产品版本
G/2010-06-29 3.0术语更新
H/2010-09-24 3.0内容更新
K/2012-05-11 4.0更新内容以符合
产品版本
This manual
The application manual contains application descriptions and setting guidelines
sorted per function. The manual can be used to find out when and for what purpose
a typical protection function can be used. The manual can also be used when
calculating settings.
1.2 Intended audience
This manual addresses the protection and control engineer responsible for
planning, pre-engineering and engineering.
The protection and control engineer must be experienced in electrical power
engineering and have knowledge of related technology, such as protection schemes
and principles.
1.3 Product documentation
1.3.1 Product documentation set
The application manual contains application descriptions and setting guidelines
sorted per function. The manual can be used to find out when and for what purpose
a typical protection function can be used. The manual can also be used when
calculating settings.
The communication protocol manual describes a communication protocol
supported by the IED. The manual concentrates on vendor-specific implementations.
The engineering guide provides information for IEC 61850 engineering of the 615
series protection IEDs with PCM600 and IET600. This guide concentrates
especially on the configuration of GOOSE communication with these tools. The
guide can be used as a technical reference during the engineering phase,
installation and commissioning phase, and during normal service. For more details
on tool usage, see the PCM600 documentation.
The engineering manual contains instructions on how to engineer the IEDs using
the different tools in PCM600. The manual provides instructions on how to set up a
PCM600 project and insert IEDs to the project structure. The manual also
1MRS756378 K Section 1
Introduction
REF615 5
Application Manual
recommends a sequence for engineering of protection and control functions, LHMI
functions as well as communication engineering for IEC 61850 and other
supported protocols.
The installation manual contains instructions on how to install the IED. The
manual provides procedures for mechanical and electrical installation. The chapters
are organized in chronological order in which the IED should be installed.
The operation manual contains instructions on how to operate the IED once it has
been commissioned. The manual provides instructions for monitoring, controlling
and setting the IED. The manual also describes how to identify disturbances and
how to view calculated and measured power grid data to determine the cause of a
fault.
The point list manual describes the outlook and properties of the data points
specific to the IED. The manual should be used in conjunction with the
corresponding communication protocol manual.
The technical manual contains application and functionality descriptions and lists
function blocks, logic diagrams, input and output signals, setting parameters and
technical data sorted per function. The manual can be used as a technical reference
during the engineering phase, installation and commissioning phase, and during
normal service.
1.3.2 Document revision history
Document revision/date Product version History
A/2007-12-20 1.0 First release
B/2008-02-08 1.0 Content updated
C/2008-07-02 1.1 Content updated to correspond to the
product version
D/2009-03-04 2.0 Content updated to correspond to the
product version
E/2009-07-03 2.0 Content updated
F/2010-06-11 3.0 Content updated to correspond to the
product version
G/2010-06-29 3.0 Terminology updated
H/2010-09-24 3.0 Content updated
K/2012-05-11 4.0 Content updated to correspond to the
product version
