OCAHG 492838402 以太网模块备件工控卡件
或
ROVPTOV1操作WPWDE2操作WPWDE1操作ROVPTOV2操作ROVPTOV3操作或
ARCSARC1-arc_flt_det
ARCSARC2-arc_flt_det
ARCSARC3-arc_flt_det
ARCSARC1运行ARCSARC2运行ARCSARC3运行DARREC1 inpro DARREC2-close_cb
DARREC1-UNSC_recl
TCSCBR2闭塞报警
BI 1（阻塞）
BI 2（断路器关闭）
BI 3（断路器开路）
TRPPTRC1-跳闸或
TRPPTRC2-跳闸
TCSCBR1阻塞报警或LED9（TCS报警）
干扰记录器
A071324 V6 EN
图17：干扰记录器
来自保护级的所有启动和运行信号都被路由以触发
干扰记录器，或仅由干扰记录
记录器取决于参数设置。此外，选择
自动重合闸、电弧保护信号和X120的三个二进制输入为
也连接。
包括两个独立的跳闸电路监控功能，用于PO3的TCSCBR1
（X100:15-19）和用于PO4的TCSCBr2（X100:20-24）。两个功能都被阻止
通过主跳闸（TRPPTRC1和TRPPTRC2）和断路器断开
信号TCS报警指示连接至LED 9。
1MRS756378 K第3节
REF615标准配置
参考文献615:47
应用手册
默认情况下，预期中没有外部电阻器
断路器跳闸线圈电路与电路并联
断路器常开辅助触点。
3.4.3.3控制和联锁功能图
PHLPTOC1操作PHHPTOC1操作PHHPTOC2操作PHIPTOC1操作NSPTOC1操作NSPTOC2操作
跳闸线圈1 PO3 TRPPTRC1块操作RST_LKOUT
带锁定模式选择的跳闸CL_LKOUT
TRPPTRC2块操作RST_LKOUT
带锁定模式选择的跳闸CL_LKOUT
DEFLPDEF2操作DEFHPDEF1操作EFPADM1操作EFPADM2操作EFPADM3操作INTRPTEF1操作ROVPTOV1操作ROVPTOV3操作ROVPTOV2操作ARCSARC1操作ARCSARC2操作ARCSARC3操作
PHLPTOC1运行PHHPTOC1运行PHHPTOC2运行PHIPTOC1运行NSPTOC1运行NSPTOC运行
PDNSPTOC1操作DEFLPDEF1操作EFHPTOC1操作或
DEFLPDEF2操作DEFHPDEF1操作EFPADM1操作EFPADM2操作EFPADM3操作INTRPTEF1操作ROVPTOV1操作ROVPTOV3操作ROVPTOV2操作ARCSARC1操作ARCSARC2操作ARCSARC3操作CCBRBRF1 trret
WPWDE1操作WPWDE2操作WPWDE3操作
WPWDE1操作WPWDE2操作WPWDE3操作
开路断路器/
跳闸线圈2
A071326 V6 EN
图18：主跳闸
来自保护装置的操作信号连接至双跳闸输出
通过相应的主设备联系PO3（X100:15-19）和PO4（X100:20-24）
跳闸TRPPTRC1和TRPPTRC2。断路器的断开控制命令
从本地或远程CBXCBR1-exe_op或自动重合闸器DARREC1-
open_ cb直接连接到输出PO3（X100:15-19）。
TRPPTRC1和2提供锁定/闭锁功能、事件生成和
跳闸信号持续时间设置。如果选择了锁定操作模式，则一个二进制
第3节1MRS756378 K
REF615标准配置
48参考文献615
应用手册
输入可重新分配给主跳闸的RST_LKOUT输入，以启用
带有按钮的外部重置。
A071328 V5 EN
图19：断路器控制
ENA_CLOSE输入可使断路器闭合，是
断路器控制功能块CBXCBR中的主跳闸状态。公开
始终启用操作。
如果ENA_CLOSE信号从断路器完全移除
带有PCM600的控制功能块CBXCBR，该功能
假设连续允许断路器闭合命令。
1MRS756378 K第3节
REF615标准配置
参考文献615:49
应用手册
TPGAPC1输入1输出1输入2输出2+
通用报警/指示1和2
启动指示
操作指示SO1
二氧化硫
PHLPTOC1启动
PHHPTOC1启动
PHHPTOC2启动
PHIPTOC1启动
NSPTOC1启动
NSPTOC2启动
PDNSPTOC1启动
DEFLPDEF1启动
EFHPTOC1启动
或
DEFLPDEF2启动
DEFHPDEF1启动
EFPADM1启动
EFPADM2启动
EFPADM3启动
INTRPTEF1开始
ROVPTOV1启动
ROVPTOV3启动
ROVPTOV2启动
WPWDE1启动
WPWDE2启动
WPWDE3启动
PHLPTOC1运行PHHPTOC1运行PHHPTOC2运行PHIPTOC1运行NSPTOC1运行NSPTOC运行
PDNSPTOC1操作DEFLPDEF1操作EFHPTOC1操作或
DEFLPDEF2操作DEFHPDEF1操作EFPADM1操作EFPADM2操作EFPADM3操作INTRPTEF1操作ROVPTOV1操作ROVPTOV3操作ROVPTOV2操作ARCSARC1操作ARCSARC2操作ARCSARC3操作WPWDE1操作WPWDE2操作WPWDE3操作A071330 V5 EN
图20：报警指示
连接IED的信号输出，以提供以下方面的专用信息：
•启动任何保护功能SO1（X100:10-12）
•任何保护功能SO2的运行（跳闸）（X100:13-15）
TPGAPC是定时器，用于设置输出的小脉冲长度。
IED中有四个通用定时器（TPGAPC1..4）。剩下的
功能图中未描述的功能可在PCM600中用于：
连接（如适用）。 OCAHG 492838402 以太网模块备件工控卡件
 OCAHG 492838402 以太网模块备件工控卡件
OR
ROVPTOV1-operate WPWDE2-operate WPWDE1-operate ROVPTOV2-operate ROVPTOV3-operate OR
ARCSARC1-arc_flt_det
ARCSARC2-arc_flt_det
ARCSARC3-arc_flt_det
ARCSARC1-operate ARCSARC2-operate ARCSARC3-operate DARREC1-inpro DARREC1-close_cb
DARREC1-unsuc_recl
TCSSCBR2 BLOCK ALARM
BI 1 (Blocking)
BI 2 (CB Closed)
BI 3 (CB Open)
TRPPTRC1 - trip OR
TRPPTRC2 - trip
TCSSCBR1 BLOCK ALARM OR LED9 (TCS ALARM)
DISTURBANCE RECORDER
A071324 V6 EN
Figure 17: Disturbance recorder
All start and operate signals from the protection stages are routed to trigger the
disturbance recorder or alternatively only to be recorded by the disturbance
recorder depending on the parameter settings. Additionally, the selected
autorecloser, the ARC protection signals and the three binary inputs from X120 are
also connected.
Two separate trip circuit supervision functions are included, TCSSCBR1 for PO3
(X100:15-19) and TCSSCBR2 for PO4 (X100:20-24). Both functions are blocked
by the Master Trip (TRPPTRC1 and TRPPTRC2) and the circuit breaker open
signal. The TCS alarm indication is connected to LED 9.
1MRS756378 K Section 3
REF615 standard configurations
REF615 47
Application Manual
By default it is expected that there is no external resistor in the
circuit breaker tripping coil circuit connected parallel with circuit
breaker normally open auxiliary contact.
3.4.3.3 Functional diagrams for control and interlocking
PHLPTOC1-operate PHHPTOC1-operate PHHPTOC2-operate PHIPTOC1-operate NSPTOC1-operate NSPTOC2-operat
trip coil 1 PO3 TRPPTRC1 BLOCK OPERATE RST_LKOUT
TRIP CL_LKOUT With lock-out mode selection
TRPPTRC2 BLOCK OPERATE RST_LKOUT
TRIP CL_LKOUT With lock-out mode selection
DEFLPDEF2-operate DEFHPDEF1-operate EFPADM1-operate EFPADM2-operate EFPADM3-operate INTRPTEF1-operate ROVPTOV1-operate ROVPTOV3-operate ROVPTOV2-operate ARCSARC1-operate ARCSARC2-operate ARCSARC3-operate
PHLPTOC1-operate PHHPTOC1-operate PHHPTOC2-operate PHIPTOC1-operate NSPTOC1-operate NSPTOC2-operate
PDNSPTOC1-operate DEFLPDEF1-operate EFHPTOC1-operate OR
DEFLPDEF2-operate DEFHPDEF1-operate EFPADM1-operate EFPADM2-operate EFPADM3-operate INTRPTEF1-operate ROVPTOV1-operate ROVPTOV3-operate ROVPTOV2-operate ARCSARC1-operate ARCSARC2-operate ARCSARC3-operate CCBRBRF1-trret
WPWDE1-operate WPWDE2-operate WPWDE3-operate
WPWDE1-operate WPWDE2-operate WPWDE3-operate
Open CB /
trip coil 2
A071326 V6 EN
Figure 18: Master trip
The operate signals from the protections are connected to the two trip output
contacts PO3 (X100:15-19) and PO4 (X100:20-24) via the corresponding Master
Trips TRPPTRC1 and TRPPTRC2. Open control commands to the circuit breaker
from local or remote CBXCBR1-exe_op or from the auto-recloser DARREC1-
open_cb are connected directly to the output PO3 (X100:15-19).
TRPPTRC1 and 2 provide the lockout/latching function, event generation and the
trip signal duration setting. If the lockout operation mode is selected, one binary
Section 3 1MRS756378 K
REF615 standard configurations
48 REF615
Application Manual
input can be reassigned to the RST_LKOUT input of the Master Trip to enable
external reset with a push button.
A071328 V5 EN
Figure 19: Circuit breaker control
The ENA_CLOSE input, which enables the closing of the circuit breaker, is a
status of the Master Trip in the breaker control function block CBXCBR. The open
operation is always enabled.
If the ENA_CLOSE signal is completely removed from the breaker
control function block CBXCBR with PCM600, the function
assumes that the breaker close commands are allowed continuously.
1MRS756378 K Section 3
REF615 standard configurations
REF615 49
Application Manual
TPGAPC1 IN1 OUT1 IN2 OUT2 +
COMMON ALARM / INDICATION 1 & 2
Start Indication
Operate Indication SO1
SO2
PHLPTOC1-start
PHHPTOC1-start
PHHPTOC2-start
PHIPTOC1-start
NSPTOC1-start
NSPTOC2-start
PDNSPTOC1-start
DEFLPDEF1-start
EFHPTOC1-start
OR
DEFLPDEF2-start
DEFHPDEF1-start
EFPADM1-start
EFPADM2-start
EFPADM3-start
INTRPTEF1-start
ROVPTOV1-start
ROVPTOV3-start
ROVPTOV2-start
WPWDE1-start
WPWDE2-start
WPWDE3-start
PHLPTOC1-operate PHHPTOC1-operate PHHPTOC2-operate PHIPTOC1-operate NSPTOC1-operate NSPTOC2-operate
PDNSPTOC1-operate DEFLPDEF1-operate EFHPTOC1-operate OR
DEFLPDEF2-operate DEFHPDEF1-operate EFPADM1-operate EFPADM2-operate EFPADM3-operate INTRPTEF1-operate ROVPTOV1-operate ROVPTOV3-operate ROVPTOV2-operate ARCSARC1-operate ARCSARC2-operate ARCSARC3-operate WPWDE1-operate WPWDE2-operate WPWDE3-operate A071330 V5 EN
Figure 20: Alarm indication
The signal outputs from the IED are connected to give dedicated information on:
• Start of any protection function SO1 (X100:10-12)
• Operation (trip) of any protection function SO2 (X100: 13-15)
TPGAPC are timers and used for setting the minimum pulse length for the outputs.
There are four generic timers (TPGAPC1..4) available in the IED. The remaining
ones not described in the functional diagram are available in PCM600 for
connection where applicable.
| OCAHG 492838402 以太网模块备件工控卡件 | | | |
