PM865K01 3BSE031151R1 张力控制器
说明1和2
启动指示
操作指示SO1
二氧化硫
PHLPTOC1启动
PHHPTOC1启动
PHHPTOC2启动
PHIPTOC1启动
NSPTOC1启动
NSPTOC2启动
PDNSPTOC1启动
DEFLPDEF1启动
EFHPTOC1启动
或
DEFLPDEF2启动
DEFHPDEF1启动
EFPADM1启动
EFPADM2启动
EFPADM3启动
INTRPTEF1开始
ROVPTOV1启动
ROVPTOV3启动
ROVPTOV2启动
WPWDE1启动
WPWDE2启动
WPWDE3启动
PHLPTOC1运行PHHPTOC1运行PHHPTOC2运行PHIPTOC1运行NSPTOC1运行NSPTOC运行
PDNSPTOC1操作DEFLPDEF1操作EFHPTOC1操作或
DEFLPDEF2操作DEFHPDEF1操作EFPADM1操作EFPADM2操作EFPADM3操作INTRPTEF1操作ROVPTOV1操作ROVPTOV3操作ROVPTOV2操作ARCSARC1操作ARCSARC2操作ARCSARC3操作WPWDE1操作WPWDE2操作WPWDE3操作
PHLPTOC1操作PHHPTOC1操作PHHPTOC2操作PHIPTOC1操作DEFLPDEF1操作EFHPTOC1或
DEFLPDEF2操作DEFHPDEF1操作EFPADM1操作EFPADM2操作EFPADM3操作INTRPTEF1操作ROVPTOV1操作ROVPTOV3操作ROVPTOV2操作
或
TPGAPC2输入1输出1输入2输出2
WPWDE1操作WPWDE2操作WPWDE3操作21
A071346 V6 EN
图29：报警指示
连接IED的信号输出，以提供以下方面的专用信息：
•启动任何保护功能SO1（X100:10-12）
•任何保护功能SO2的运行（跳闸）（X100:13-15）
第3节1MRS756378 K
REF615标准配置
66参考文献615
应用手册
TPGAPC是定时器，用于设置输出的小脉冲长度。
IED中有四个通用定时器（TPGAPC1..4）。剩下的
功能图中未描述的功能可在PCM600中用于：
连接（如适用）。
3.6标准配置C
3.6.1应用
无方向过电流和无方向接地故障保护的标准配置主要用于电缆和架空线路馈线应用
直接接地或电阻接地配电网。
默认情况下，具有标准配置的IED从工厂交付
设置和参数。终端用户在传入、传出和
IED内的内部信号指定使该配置更进一步
适用于不同的主电路布局和相关功能需求
使用PCM600修改内部功能。
3.6.2功能
表21：标准中包含的功能 PM865K01 3BSE031151R1 张力控制器
 PM865K01 3BSE031151R1 张力控制器
NDICATION 1 & 2
Start Indication
Operate Indication SO1
SO2
PHLPTOC1-start
PHHPTOC1-start
PHHPTOC2-start
PHIPTOC1-start
NSPTOC1-start
NSPTOC2-start
PDNSPTOC1-start
DEFLPDEF1-start
EFHPTOC1-start
OR
DEFLPDEF2-start
DEFHPDEF1-start
EFPADM1-start
EFPADM2-start
EFPADM3-start
INTRPTEF1-start
ROVPTOV1-start
ROVPTOV3-start
ROVPTOV2-start
WPWDE1-start
WPWDE2-start
WPWDE3-start
PHLPTOC1-operate PHHPTOC1-operate PHHPTOC2-operate PHIPTOC1-operate NSPTOC1-operate NSPTOC2-operate
PDNSPTOC1-operate DEFLPDEF1-operate EFHPTOC1-operate OR
DEFLPDEF2-operate DEFHPDEF1-operate EFPADM1-operate EFPADM2-operate EFPADM3-operate INTRPTEF1-operate ROVPTOV1-operate ROVPTOV3-operate ROVPTOV2-operate ARCSARC1-operate ARCSARC2-operate ARCSARC3-operate WPWDE1-operate WPWDE2-operate WPWDE3-operate
PHLPTOC1-operate PHHPTOC1-operate PHHPTOC2-operate PHIPTOC1-operate DEFLPDEF1-operate EFHPTOC1-operate OR
DEFLPDEF2-operate DEFHPDEF1-operate EFPADM1-operate EFPADM2-operate EFPADM3-operate INTRPTEF1-operate ROVPTOV1-operate ROVPTOV3-operate ROVPTOV2-operate
OR
TPGAPC2 IN1 OUT1 IN2 OUT2
WPWDE1-operate WPWDE2-operate WPWDE3-operate 21
A071346 V6 EN
Figure 29: Alarm indication
The signal outputs from the IED are connected to give dedicated information on:
• Start of any protection function SO1 (X100:10-12)
• Operation (trip) of any protection function SO2 (X100: 13-15)
Section 3 1MRS756378 K
REF615 standard configurations
66 REF615
Application Manual
TPGAPC are timers and used for setting the minimum pulse length for the outputs.
There are four generic timers (TPGAPC1..4) available in the IED. The remaining
ones not described in the functional diagram are available in PCM600 for
connection where applicable.
3.6 Standard configuration C
3.6.1 Applications
The standard configuration for non-directional overcurrent and non-directional earthfault protection is mainly intended for cable and overhead-line feeder applications
in directly or resistance earthed distribution networks.
The IED with a standard configuration is delivered from the factory with default
settings and parameters. The end-user flexibility for incoming, outgoing and
internal signal designation within the IED enables this configuration to be further
adapted to different primary circuit layouts and the related functionality needs by
modifying the internal functionality using PCM600.
3.6.2 Functions
Table 21: Functions included in the standard | PM865K01 3BSE031151R1 张力控制器 | | | |
