ABB 70PR05B-ES HESG332204R0001 伺服控制器接口卡 顺丰包邮
当ENA_CLOSE输入被激活时，断路器闭合被启用。
输入可由配置逻辑激活，配置逻辑是
隔离开关或断路器支架和接地开关位置状态以及状态
主跳闸逻辑、气压报警和断路器弹簧充电。
DCSXSWI的OKPOS输出定义了隔离开关或断路器卡车是否：
对打开（测试位置）或关闭（维修位置）。这个，一起
在接地开关断开和非激活跳闸信号的情况下，激活闭合启用
向断路器控制功能块发送信号。开放操作始终是
启用。自动重合闸关闭命令信号直接连接到
输出触点PO1（X100:6-7）。
例如，ITL_BYPASS输入可用于始终启用关闭
当断路器支架处于试验位置时，断路器
当断路器转向架闭合时，联锁条件激活
服务位置。
如果ENA_ CLOSE和BLK_
从断路器控制功能块CBXCBR中删除
PCM600，该功能假设断路器关闭命令
连续允许。
第3节1MRS756378 K
REF615标准配置
108参考文献615
应用手册
TPGAPC1输入1输出1输入2输出2+
PHLPTOC1运行PHHPTOC1运行PHHPTOC2运行PHIPTOC1运行NSPTOC1运行NSPTOC运行
PDNSPTOC1操作DEFLPDEF1操作EFHPTOC1操作或
DEFLPDEF2操作DEFHPDEF1操作EFPADM1操作EFPADM2操作EFPADM3操作INTRPTEF1操作ROVPTOV1操作ROVPTOV3操作ROVPTOV2操作ARCSARC1操作ARCSARC2操作ARCSARC3操作WPWDE1操作WPWDE2操作WPWDE3操作PHHPTOC1操作PHHPTOC2操作PHPTOC1操作EFHPTOC1操作或
DEFLPDEF2操作DEFHPDEF1操作EFPADM1操作EFPADM2操作EFPADM3操作INTRPTEF1操作ROVPTOV1操作ROVPTOV3操作ROVPTOV2操作
或
TPGAPC2输入1输出1输入2输出2
WPWDE1操作WPWDE2操作WPWDE3操作21
GUID-572DA8CC-7A7D-4F9F-87C5-272A4283FB3E V3 EN
图55：报警指示
断路器状态监控功能（SSCBR）监控电路
基于连接和测量的二进制输入信息的断路器状态
当前水平。该功能介绍了各种监督方法。这个
相应的监控报警信号被发送至LED 8。
1MRS756378 K第3节
REF615标准配置
参考文献615:109
应用手册
连接IED的信号输出，以提供以下方面的专用信息：
•启动任何保护功能SO1（X100:10-12）
•任何保护功能SO2的运行（跳闸）（X100:13-14）
•过电流保护功能SO2任何阶段的运行（跳闸）
（X110:17-19）
•接地故障保护功能SO3任何阶段的运行（跳闸）
（X110:20-22）
TPGAPC是定时器，用于设置输出的小脉冲长度。
IED中有四个通用定时器（TPGAPC1..4）。剩下的
功能图中未描述的功能可在PCM600中用于：
连接（如适用）。
3.9标准配置F
3.9.1应用
定向过电流和定向接地故障的标准配置
相电压测量、欠压和过压保护
保护主要用于综合保护和控制
断路器控制异步电动机的功能。未成年人
修改：该标准配置也适用于接触器
由电机控制。该配置还包括根据导纳、功率或谐波原理选择接地故障保护的附加选项。
默认情况下，具有标准配置的IED从工厂交付
设置和参数。终端用户在传入、传出和
IED内的内部信号指定使该配置更进一步
适用于不同的主电路布局和相关功能需求
使用PCM600修改内部功能。
3.9.2功能
表38：标准中包含的功能 ABB 70PR05B-ES HESG332204R0001 伺服控制器接口卡 顺丰包邮
 ABB 70PR05B-ES HESG332204R0001 伺服控制器接口卡 顺丰包邮
he circuit breaker closing is enabled when the ENA_CLOSE input is activated.
The input can be activated by the configuration logic, which is a combination of
the disconnector or breaker truck and earth-switch position statuses and the statuses
of the master trip logics and gas pressure alarm and circuit-breaker spring charging.
The OKPOS output from DCSXSWI defines if the disconnector or breaker truck is
definitely either open (in test position) or close (in service position). This, together
with the open earth-switch and non-active trip signals, activates the close-enable
signal to the circuit breaker control function block. The open operation is always
enabled. The auto-recloser close command signals are directly connected to the
output contact PO1 (X100:6-7).
The ITL_BYPASS input can be used, for example, to always enable the closing of
the circuit breaker when the circuit breaker truck is in the test position, despite of
the interlocking conditions being active when the circuit breaker truck is closed in
service position.
If the ENA_CLOSE and BLK_CLOSE signals are completely
removed from the breaker control function block CBXCBR with
PCM600, the function assumes that the breaker close commands
are allowed continuously.
Section 3 1MRS756378 K
REF615 standard configurations
108 REF615
Application Manual
TPGAPC1 IN1 OUT1 IN2 OUT2 +
PHLPTOC1-operate PHHPTOC1-operate PHHPTOC2-operate PHIPTOC1-operate NSPTOC1-operate NSPTOC2-operate
PDNSPTOC1-operate DEFLPDEF1-operate EFHPTOC1-operate OR
DEFLPDEF2-operate DEFHPDEF1-operate EFPADM1-operate EFPADM2-operate EFPADM3-operate INTRPTEF1-operate ROVPTOV1-operate ROVPTOV3-operate ROVPTOV2-operate ARCSARC1-operate ARCSARC2-operate ARCSARC3-operate WPWDE1-operate WPWDE2-operate WPWDE3-operate PHHPTOC1-operate PHHPTOC2-operate PHIPTOC1-operate DEFLPDEF1-operate EFHPTOC1-operate OR
DEFLPDEF2-operate DEFHPDEF1-operate EFPADM1-operate EFPADM2-operate EFPADM3-operate INTRPTEF1-operate ROVPTOV1-operate ROVPTOV3-operate ROVPTOV2-operate
OR
TPGAPC2 IN1 OUT1 IN2 OUT2
WPWDE1-operate WPWDE2-operate WPWDE3-operate 21
GUID-572DA8CC-7A7D-4F9F-87C5-272A4283FB3E V3 EN
Figure 55: Alarm indication
The circuit breaker condition monitoring function (SSCBR) supervises the circuit
breaker status based on the binary input information connected and measured
current levels. The function introduces various supervision methods. The
corresponding supervision alarm signals are routed to LED 8.
1MRS756378 K Section 3
REF615 standard configurations
REF615 109
Application Manual
The signal outputs from the IED are connected to give dedicated information on:
• Start of any protection function SO1 (X100:10-12)
• Operation (trip) of any protection function SO2 (X100:13-14)
• Operation (trip) of any stage of the overcurrent protection function SO2
(X110:17-19)
• Operation (trip) of any stage of the earth-fault protection function SO3
(X110:20-22)
TPGAPC are timers and used for setting the minimum pulse length for the outputs.
There are four generic timers (TPGAPC1..4) available in the IED. The remaining
ones not described in the functional diagram are available in PCM600 for
connection where applicable.
3.9 Standard configuration F
3.9.1 Applications
The standard configuration for directional overcurrent and directional earth-fault
protection with phase-voltage based measurements, undervoltage and overvoltage
protection is mainly intended for comprehensive protection and control
functionality of circuit breaker controlled asynchronous motors. With minor
modifications this standard configuration can be applied also for contactor
controlled motors. The configuration also includes additional options to select earthfault protection based on admittance, wattmetric or harmonic based principle.
The IED with a standard configuration is delivered from the factory with default
settings and parameters. The end-user flexibility for incoming, outgoing and
internal signal designation within the IED enables this configuration to be further
adapted to different primary circuit layouts and the related functionality needs by
modifying the internal functionality using PCM600.
3.9.2 Functions
Table 38: Functions included in the standard | ABB 70PR05B-ES HESG332204R0001 伺服控制器接口卡 顺丰包邮 | | | |
