6SM 56-S 3000-G 伺服自动化电机 控制传输速度 Kollmorgen
–连接或断开电缆
–将装置复位或切换至手动操作
•对于危险场所，适用特殊限制，见附录E，
标准。
•安装过程中，切勿将设备连接到主电源
工作
•将系统连接到主电源时，要格外小心。
不正确的操作可能导致受伤或死亡。
•确保所有操作或维护设备的人员都知道
设备隔离安全开关的准确位置和操作方法
以及主电源隔离开关。
•检查了工艺子部分，并进行了试运行
执行时，负责人必须检查联锁链等
必须充分告知相关人员将要进行的试运行
执行。
•测试和操作工艺时，工艺技术人员应在场
物体。
•如果存在任何不确定性，切勿激活任何系统初始化按钮
存在关于初始化期间系统内发生的确切信息。
总是先检查。
•始终记住，控制系统可以通过
远程工程站，通过控制连接到另一个节点
网络
•记住，AC 800M控制器将在电压
应用。
采取措施使流程处于安全状态，提高了
电源、通信链路或控制系统部件时的安全
失败例如，这些步骤可能需要安装阀门或继电器
自动返回故障安全位置。
3BSE036351-600 A 15
安全总结（续）
产品安全
必须始终遵守以下安全规则：
•为避免释放静电，将自己和任何工具接地
在处理印刷电路板、电池、存储卡和其他
设备的敏感部件
•所有电子设备对ESD（静电放电）敏感。到
处理印刷电路板时避免意外损坏
建议佩戴腕带，接地至底盘。带子必须
具有内置保护电阻器
•储存和运输时必须使用防静电导电塑料袋
运输中的PC板。
16 3BSE036351-600 A
安全总结（续）
更换装置前
维修
操作环境
在AC 800M控制器系统联机之前，调查
环境条件适用。特别注意到：
以下是：
更换装置的所有程序可通过参考相关
文档
在系统电源连接的情况下拆卸或更换单元可能会导致人身伤害
人员和设备损坏。因此，这是至关重要的
拆除前，在工艺侧完全断开电源
或者进行单元的插入。
参见第206页的在线更换装置和I/O文件。
建议保持适当的备件库存，以：
避免系统停机。
确保在以下位置制作当前应用程序的备份副本：
以避免系统停机。 6SM 56-S 3000-G 伺服自动化电机 控制传输速度 Kollmorgen
 6SM 56-S 3000-G 伺服自动化电机 控制传输速度 Kollmorgen– connecting or disconnecting cables
– resetting or switching units to manual operation
• For hazardous locations special restrictions apply, see Appendix E,
Standards.
• Never connect the equipment to the mains power supply during installation
work.
• Take extreme care when connecting the system to the mains power supply.
Injury or death can be the result of incorrect procedures.
• Ensure that all personnel operating or maintaining the installation know the
exact location of and how to operate the equipment isolating safety switch
and the mains power supply isolating switch.
• When the process sub-sections have been checked and a test run has been
performed, a person responsible must check the interlocking chains etc. All
concerned personnel must be fully informed regarding test runs to be
performed.
• Process technicians are to be present when testing and operating process
objects.
• Never activate any System Initialization push-button if any uncertainty
exists regarding exactly what occurs within the system during initialization.
ALWAYS CHECK FIRST.
• Remember at all times, that the control system can be controlled from a
remote engineering station, connected at another node via Control
Network.
• Remember, the AC 800M Controller will start automatically when voltage
is applied.
Taking steps to bring the process to a safe state, provides an improved level of
safety when power supplies, communication links or parts of the control system
fail. Such steps may require, for example, the installation of valves or relays that
automatically return to a fail-safe position.
3BSE036351-600 A 15
Safety Summary (continued)
Product Safety
The following safety rules must be observed at all times:
• To avoid discharging static electricity, ground both yourself and any tools
before handling printed circuit boards, batteries, memory cards, and other
sensitive pieces of the equipment
• All electronic devices are sensitive to ESD (electrostatic discharge). To
avoid accidental damage while handling printed circuit boards, it is
recommended to wear a wrist strap, grounded to the chassis. The strap must
have a built-in protective resistor
• Anti-static, conductive plastic bags must be used for storage and transport
of PC boards in transit.
16 3BSE036351-600 A
Safety Summary (continued)
Before replacing Units
Maintenance
Operating Environment
Before the AC 800M Controller system is brought online, investigate which
environmental conditions are applicable. Take note in particular of the
following:
All procedures for replacing units can be located by referring to the relevant
documentation.
Removing or replacing units with system power connected can cause injury to
personnel and damage to equipment. It is, therefore, of the utmost importance
that the power supply be fully disconnected, on the process side, before removal
or insertion of units takes place.
See Online Replacement of Unit on page 206 and I/O documentation.
It is recommended that a stock of suitable spare components be maintained to
avoid system downtime.
Ensure that back-up copies of the current application program are made at
regular, predetermined intervals to avoid system downtime.
| 6SM 56-S 3000-G 伺服自动化电机 控制传输速度 Kollmorgen | | | |
