DUE-60WKS-CE240/22PO 模块控制传输速度 Kollmorgen
文件和附录C，推荐
组件。PROFIBUS DP必须采用屏蔽双绞线连接
电缆。
表14.CI854/CI854A/CI854B–PROFIBUS DP连接器
引脚名称描述
1屏蔽屏蔽/保护接地
2–未使用
3 RxD/TxD-P接收/发送数据P线（B线）
4 CNTR-P指示到中继器的方向（TTL）
5 DGND数字地面
6 VP+5 V，用于端接电阻器
7 – –
8 RxD/TxD-N接收/发送数据N线（A线）
9 DGND数字地面
请注意，CI854单元没有单元冗余。只为
CI854A/CI854B。主总线300接口，CI855/TP853
CI855由处理器单元通过CEX总线供电，需要：
因此不需要额外的外部电源。
底板TP853提供两个以太网端口，用于连接冗余
主总线300的以太网网络。
使用以下步骤安装CI855/TP853：
1.将装置安装在DIN导轨上，参见将AC 800M装置安装到DIN导轨上
在第71页，并在单个中安装PM85x/PM86x/TP830处理器单元
第84页的配置。
2.将以太网双绞线连接至底板上的触点。
3.将以太网电缆的另一端连接到以太网交换机。
以太网双绞线连接
以太网双绞线通过位于的10BaseT RJ45连接器连接
TP853.有关连接器的说明，请参见第90页的表5。
如果需要AUI接口，则需要10BaseT到AUI的转换器。
通信单元CI855不能向收发器供电，因此
必须使用单独的电源。
请注意，CI855单元没有单元冗余。
第2节安装安装S100 I/O接口，CI856/TP856
3BSE036351-600 A 129
安装S100 I/O接口，CI856/TP856
CI856由处理器单元通过CEX总线供电，需要：
因此不需要额外的外部电源。
使用以下步骤安装CI856/TP856：
1.将装置安装在DIN导轨上，参见将AC 800M装置安装到DIN导轨上
在第71页，并在单个中安装PM85x/PM86x/TP830处理器单元
第84页的配置。
2.将S100输入/输出电缆TK575/TK580连接至基板上的触点。A.
必须使用总线扩展器DSBC174/DSBC176/DSBC173A。
S100 I/O连接和安装
将S100 I/O机架电缆TK575/TK580连接至“I/O标签”36引脚
中心线微型带状连接器位于TP856上。
S100 I/O的安装
有关S100 I/O相关组件的安装，请参阅S100 I/O文档。
请注意，CI856单元没有单元冗余。
安装INSUM接口，CI857/TP853第2节安装
130 3BSE036351-600 A
安装INSUM接口，CI857/TP853
CI857由处理器单元通过CEX总线供电，需要：
因此不需要额外的外部电源。
使用以下步骤安装CI857/TP853：
1.将装置安装到DIN导轨上，请参阅将AC 800M装置安装在DIN导轨上
在第71页，并在单个中安装PM85x/PM86x/TP830处理器单元
第84页的配置。
2.将以太网双绞线连接到
底板（COM2不用于连接INSUM）。
3.通过以下方式将以太网电缆的另一端连接到INSUM设备
以太网/LON网关。
以太网双绞线连接
以太网双绞线通过位于的10BaseT RJ45连接器连接
TP853.有关连接器的说明，请参见第90页的表5。
请注意，CI857单元没有单元冗余。
第2节安装安装驱动总线接口，CI858/TP858
3BSE036351-600 A 131
安装驱动总线接口，CI858/TP858
CI858由处理器单元通过CEX总线供电，需要：
因此不需要额外的外部电源。该装置安装在水平面上
铁路上的嘈杂声。
将装置安装到DIN导轨上，请参阅将AC 800M装置安装在DIN导轨上
第71页，在单个中安装PM85x/PM86x/TP830处理器单元
第84页的配置和第338页的CI858和TP858–驱动总线接口。
光纤接口
CI858板通过三个光接收器/发射器连接到驱动系统
对。HP/Agilent Technologies通用链路系列（HFBR系列）光纤
使用发射器/接收器。光纤的传输速度为4Mbit/s。
表15.光连接器
连接器名称和说明
驱动总线TxD传输数据
驱动总线RxD接收数据
I/O总线TxD传输数据
I/O总线RxD接收数据
PC工具TxD传输数据
PC工具RxD接收数据
请注意，CI858单元没有单元冗余。
安装基金会现场总线高速以太网接口，CI860/TP860第2节
132 3BSE036351-600 A
安装基金会现场总线高速以太网
接口，CI860/TP860
CI860由处理器单元通过CEX总线供电，需要：
因此不需要额外的外部电源。
使用以下步骤安装CI860/TP860：
1. DUE-60WKS-CE240/22PO 模块控制传输速度 Kollmorgen
 DUE-60WKS-CE240/22PO 模块控制传输速度 Kollmorgen
documentation and Appendix C, Recommended
Components. The PROFIBUS DP must be connected with shielded twisted pair
cables.
Table 14. CI854/CI854A/CI854B – PROFIBUS DP Connector
PIN Designation Description
1 Shield Shield/protective ground
2 – Not Used
3 RxD/TxD-P Receive/Transmit Data P-line (B-line)
4 CNTR-P Indicates Direction to Repeater (TTL)
5 DGND Digital Ground
6 VP +5 V, for terminating resistors
7 – –
8 RxD/TxD-N Receive/Transmit Data N-line (A-line)
9 DGND Digital Ground
Note that there is no unit redundancy for the CI854 unit. Only for
CI854A/CI854B.the MasterBus 300 Interface, CI855/TP853
The CI855 is powered from the processor unit via the CEX-Bus and requires
therefore no additional external power source.
The baseplate, TP853, provides two Ethernet ports for connection of redundant
Ethernet network for MasterBus 300.
Use the following procedure to install the CI855/TP853:
1. Mount the unit on the DIN-rail, see Mounting AC 800M Units onto DIN-Rail
on page 71 and Installing the PM85x/PM86x/TP830 Processor Unit in Single
Configuration on page 84.
2. Connect the Ethernet twisted pair cable to the contact on the baseplate.
3. Connect the other end of the Ethernet cable to an Ethernet Switch.
Ethernet twisted pair Connection
The Ethernet twisted pair is connected via the 10BaseT RJ45 connector located on
TP853. For a description of the connector, see Table 5 on page 90.
If an interface to an AUI is required, a converter from 10BaseT to AUI is needed.
The communication unit, CI855, can not provide power to the transceiver, therefore
a separate power source must be used.
Note that there is no unit redundancy for the CI855 unit.
Section 2 Installation Installing the S100 I/O Interface, CI856/TP856
3BSE036351-600 A 129
Installing the S100 I/O Interface, CI856/TP856
The CI856 is powered from the processor unit via the CEX-Bus and requires
therefore no additional external power source.
Use the following procedure to install the CI856/TP856:
1. Mount the unit on the DIN-rail, see Mounting AC 800M Units onto DIN-Rail
on page 71 and Installing the PM85x/PM86x/TP830 Processor Unit in Single
Configuration on page 84.
2. Connect the S100 I/O cable, TK575/TK580, to the contact on the baseplate. A
bus extender, DSBC174/DSBC176/DSBC173A, must be used.
S100 I/O Connection and Installation
Connect the S100 I/O rack cable TK575/TK580 to the “I/O-labeled” 36-pin
centerline miniature ribbon connector located on TP856.
Installation of S100 I/O
For installation of the S100 I/O-related components, see S100 I/O documentation.
Note that there is no unit redundancy for the CI856 unit.
Installing the INSUM Interface, CI857/TP853 Section 2 Installation
130 3BSE036351-600 A
Installing the INSUM Interface, CI857/TP853
The CI857 is powered from the processor unit via the CEX-Bus and requires
therefore no additional external power source.
Use the following procedure to install the CI857/TP853:
1. Mount the unit onto the DIN-rail, see Mounting AC 800M Units onto DIN-Rail
on page 71 and Installing the PM85x/PM86x/TP830 Processor Unit in Single
Configuration on page 84.
2. Connect the Ethernet twisted pair cable to the COM1 connector on the
baseplate (COM2 is not used for connection to INSUM).
3. Connect the other end of the Ethernet cable to the INSUM equipment via
Ethernet/LON Gateway.
Ethernet Twisted Pair Connection
The Ethernet twisted pair is connected via the 10BaseT RJ45 connector located on
TP853. For a description of the connector see Table 5 on page 90.
Note that there is no unit redundancy for the CI857 unit.
Section 2 Installation Installing the DriveBus Interface, CI858/TP858
3BSE036351-600 A 131
Installing the DriveBus Interface, CI858/TP858
The CI858 is powered from the processor unit via the CEX bus and requires
therefore no additional external power source. The unit is mounted onto a horizontal
DIN rail.
Mount the unit onto the DIN-rail, see Mounting AC 800M Units onto DIN-Rail on
page 71, Installing the PM85x/PM86x/TP830 Processor Unit in Single
Configuration on page 84 and CI858 and TP858 – DriveBus Interface on page 338.
Optical Connectors
The CI858 board connects to the drive system via three optical receiver/transmitter
pairs. HP/Agilent Technologies Versatile Link Series (HFBR family) optical
transmitter/receivers are used. Transmission speed of the optical fibres is 4 Mbit/s.
Table 15. Optical Connectors
Connector Designation Description
DriveBus TxD Transmit data
DriveBus RxD Receive data
I/O Bus TxD Transmit data
I/O Bus RxD Receive data
PC Tools TxD Transmit data
PC Tools RxD Receive data
Note that there is no unit redundancy for the CI858 unit.
Installing the FOUNDATION Fieldbus High Speed Ethernet Interface, CI860/TP860 Section 2
132 3BSE036351-600 A
Installing the FOUNDATION Fieldbus High Speed Ethernet
Interface, CI860/TP860
The CI860 is powered from the processor unit via the CEX-Bus and requires DUE-60WKS-CE240/22PO 模块控制传输速度 Kollmorgen
| | | |
