NRP53 44206-870.00 主控制器DCS系统模块 GRUNDIG
本主题不适用于PM891处理器单元。请参阅中的安装PM891
93页的单一配置。
对于PM858/PM861/PM862/PM864/PM865/PM866/PM867，插入RCU链路
RCU链路接头处的终端插头TB852。终端插头必须：
在单一配置下运行时始终使用。
当冗余处理器在单个配置中运行时，使用RCU
链路电缆TK851，如果RCU链路终端插头TB852不可用。
2节安装：在单个配置中安装PM85x/PM86x/TP830处理器单元
3BSE036351-600 A 85
5.底板电缆连接：
a、 连接电源引线和电源监控信号（如适用）
从SS82x到螺钉端子SA和SB（参见89页图28）。
b、 将控制网络电缆连接至CN1（单连接）或CN1+
CN2（冗余连接）。
c、 将串行协议连接到COM3。
d、 使用电缆TK212将控制构建器连接到COM4（如果需要
改变IP地址等）。否则，将控件生成器连接到
控制网络。
6.将光学模块总线连接到处理器单元上的光学触点
（参见36页图2和140页图45）。关于
S800 I/O中提供了光缆选择和电缆长度
文档
7.PM8xx配有内部备用电池。当电池
使用时，将其放在内部电池支架中（参见201页图68）。
当要使用外部SB821/SB822电池单元时，根据
请参阅页的安装SB821外部电池单元中的说明
151/安装152页的SB822可充电外部电池单元。
请注意，光学模块总线的连接与处理器的连接相同
用于S800 I/O中的FCI（参见168页图59）
不要将内部备用电池放在电池座中，直到
AC 800M控制器已正常通电，内存备份
功能已激活，即B（蓄电池）LED闪烁。如果不正常
电源连接到处理器单元，电池就位，然后
CPU内存将立即开始消耗电池电量。
在单个配置中安装PM85x/PM86x/TP830处理器单元2节：安装
86 3BSE036351-600 A
安装结束时，务必安装新的内部或外部电池
阶段由于在运行期间频繁停电，原电池被大量使用
系统安装。
图25.CEX总线的TB850端子（公）
每个封装都提供一个TB850公CEX总线终端装置
（PM851K01、PM851AK01、PM 856K01、PM856AK01、PMC858K01、以及PM860K01，
PM860AK01、PM861K1、PM861AK01、PM86 2K01、PM 864K01、PM864AK01、，
PM8xx/TP830的PM865K01、PM866K01、PM866AK01和PM867K01
处理器单元。
PM851/PM851A限制为多一个CEX modu NRP53 44206-870.00 主控制器DCS系统模块 GRUNDIG
 NRP53 44206-870.00 主控制器DCS系统模块 GRUNDIG
This topic does not apply to the PM891 processor unit. See Installing PM891 in
Single Configuration on page 93.
For PM858/PM861/PM862/PM864/PM865/PM866/PM867 insert the RCU Link
Termination plug TB852, at the RCU Link connector. The termination plug must
always be used when running in single configuration.
When a redundant processor is running in a single configuration use the RCU
Link Cable TK851, if the RCU Link Termination plug TB852 is not available.
Section 2 Installation Installing the PM85x/PM86x/TP830 Processor Unit in Single Configuration
3BSE036351-600 A 85
5. Baseplate cable connections:
a. Connect the power leads and, if applicable, power supervision signals
from SS82x to screw terminals SA and SB (see Figure 28 on page 89).
b. Connect the Control Network cables to CN1 (single connection) or CN1 +
CN2 (redundant connection).
c. Connect the serial protocol to COM3.
d. Connect the Control Builder to COM4 with cable TK212 (if required for
changing an IP address etc). Otherwise connect the Control Builder to the
Control Network.
6. Connect the optical ModuleBus to the optical contacts on the processor unit
(see Figure 2 on page 36 and Figure 45 on page 140). Information regarding
optical cable selection and cable length is provided in the S800 I/O
documentation.
7. The PM8xx is supplied with an internal back-up battery. When the battery is to
be used, place it in the Internal Battery Holder (see Figure 68 on page 201).
When the external SB821/SB822 battery unit is to be used, install it according
to the instructions in Installing the SB821 External Battery Unit on page
151/Installing the SB822 Rechargeable External Battery Unit on page 152.
Note that connection to the optical ModuleBus is identical to that for the processor
unit and for the FCI in S800 I/O (see Figure 59 on page 168.)
Do not place the internal back-up battery in the battery holder until the
AC 800M Controller has been powered-up normally and the memory back-up
function has been activated, that is, the B(attery) LED flashes. If no normal
power supply is connected to the processor unit with the battery in place, then
the CPU memory will immediately start to consume battery power.
Installing the PM85x/PM86x/TP830 Processor Unit in Single Configuration Section 2 Installation
86 3BSE036351-600 A
Always install a fresh internal or external battery at the end of the installation
phase. The original battery is heavily utilized due to frequent blackouts during
system installation.
Figure 25. TB850 Terminator for CEX-Bus (male)
A TB850 male CEX-Bus termination unit is supplied with each package
(PM851K01, PM851AK01, PM856K01, PM856AK01, PM858K01, PM860K01,
PM860AK01, PM861K01, PM861AK01, PM862K01, PM864K01, PM864AK01,
PM865K01, PM866K01, PM866AK01, and PM867K01) of the PM8xx/TP830
processor unit.
PM851/PM851A is restricted to a maximum of one CEX modu NRP53 44206-870.00 主控制器DCS系统模块 GRUNDIG
| | | |
