80156-815-54-R 80173-005-01 模块备件

产品标题：80156-815-54-R 80173-005-01 IGCT可控硅 A-B

产品参数：

型号：80156-815-54-R 80173-005-01

原产地：美国

质保：七天验收期，质保期一年

品牌：A-B

产品图片展示

 

产品详情资料​
ck机柜空气过滤器。必要时进行清洁或更换。检查空气滤清器在非常脏的环境中更频繁。3个月检查机柜和模块是否有灰尘。必要时使用防静电真空进行清洁。检查机柜内的所有模块信号、电源和接地连接。验证他们是安全的。请参阅步骤。检查模块电路板，特别注意电源触点和边缘连接器。必要时进行清洁。请参阅步骤。12个月完成此表中的所有任务。关闭警告切勿使用带电电源清洁电气零件或部件目前这样做会使您面临电击危险。使用清洁溶剂时，请佩戴护目镜。从印刷电路板上去除溶剂时使用压缩空气，飞溅可能导致眼睛受伤溶剂从印刷电路板上移除时。
预防性维护程序WBPEEUI240766B0 7-3印刷电路板清洗本节中有几个电路板清洁程序。这些程序包括电路板清洁和清洗、清洁边缘连接器和电路板层压板在边缘连接器之间。使用符合每个电路板的需求。清除电路板上的所有灰尘、污垢、油、腐蚀或任何其他污染物。在以下位置对印刷电路板进行所有清洁和搬运：静态安全工作站。始终遵守以下步骤：处理印刷电路时第3节中的特殊处理董事会。一般清洁和清洗如果印刷电路板需要轻微清洁，请清除灰尘以及印刷电路板表面的残留物，干燥、过滤的压缩空气或抗静电现场服务真空吸尘器。清洗印刷电路板：1.通过喷涂或擦拭清洁印刷电路板使用异丙醇（99.5%电子级）。使用泡沫用尖拭子擦拭电路板。2.用压缩空气吹除过量溶剂没有电路板。边缘连接器清洁1.使用80%异丙醇（99.5%）的溶剂混合物电子级）和20%蒸馏水。2.用溶剂混合物浸泡无绒布。3.平行于边缘连接器触点来回操作布。4.用浸有溶剂的干净布重复5.干燥边缘接头ck cabinet air filters. Clean or replace them as necessary. Check the air filter
more frequently in excessively dirty environments.3 monthsCheck cabinet and module for dust. Clean as necessary using an antistatic vacuum.Check all module signal, power and ground connections within the cabinet. Verifythat they are secure. Refer to procedure.Check module circuit board, giving special attention to power contacts and edgeconnectors. Clean as necessary. Refer to procedure.12 monthsComplete all tasks in this table. ShutdownWARNINGNever clean electrical parts or components with live powerpresent. Doing so exposes you to an electrical shock hazard.Wear eye protection whenever working with cleaning solvents.When removing solvents from printed circuit boards usingcompressed air, injury to the eyes could result from splashingsolvent as it is removed from the printed circuit board.Preventive Maintenance ProceduresWBPEEUI240766B0 7 - 3Printed Circuit Board CleaningThere are several circuit board cleaning procedures in this section. These procedures cover circuit board cleaning and washing, cleaningedge connectors and circuit board laminatebetween edge connectors. Use the procedures that meet theneeds of each circuit board. Remove all dust, dirt, oil, corrosion or any other contaminant from the circuit board.
Do all cleaning and handling of the printed circuit boards atstatic safe work stations. Always observe the steps underSpecial Handling in Section 3 when handling printed circuitboards.General Cleaning and WashingIf the printed circuit board needs minorcleaning, remove dustand residue from the printed circuit board surface using clean,dry, filtered compressed air or an antistatic field service vacuum cleaner.To wash the printed circuit board:1. Clean the printed circuit board by spraying or wiping itith isopropyl alcohol (99.5% electronic grade). Use a foamtipped swab to wipe the circuit board.2. Remove excess solvent by using compressed air to blow itfree of the circuit board.Edge Connector Cleaning1. Use a solvent mixture of 80% isopropyl alcohol (99.5%electronic grade) and 20%distilled water.2. Soak a lint-free cloth with the solvent mixture.3. Work the cloth back and forth parallel to theedge connector contacts.4.Repeat with a clean cloth that is soaked with the solventmixture.5. Dry the edge connecto

主营产品简介
专注于DCS、PLC、机器人控制系统、大型伺服四大系统领域。

主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。

优势：供应进口原装正品，专业停产配件，

发货快，货期精准，

主营品牌包括 ABB贝利、GE/FUANC、FOXBORO、英维思TRICONEX 、本特利BENTLY、A-B罗克韦尔、艾默生EMERSON 、OVATION、MOTOROLA、XYVOM、霍尼韦尔HONEYWELL 、力士乐REXROTH、KUKA、NI、DEIF、横河、伍德沃德WOODWARD、瑞恩、施耐德SCHNEIDER 、安川、 穆格MOOG、PROSOFT等品牌