80190-920-03-R 80190-119-018 18 模块备件

产品标题：80190-920-03-R 80190-119-018 18脉冲驱动控制 A-B

产品参数：

型号：80190-920-03-R 80190-119-018  

原产地：美国

质保：七天验收期，质保期一年

品牌：A-B

产品图片展示

 

产品详情资料
d用拭子擦拭电路板。2.用压缩空气吹除过量溶剂没有电路板。
边缘连接器清洁1.使用80%异丙醇（99.5%）的溶剂混合物电子级）和20%蒸馏水。2.用溶剂混合物浸泡无绒布。3.平行于边缘连接器触点来回操作布4.用浸有溶剂的干净布重复
混合物5.用清洁剂擦拭边缘连接器接触区域不起毛的布。7-4 WBPEEUI240766B0预防性维护程序要清洁污损或深度污染的边缘连接器触点：1.使用非研磨橡皮擦或等效物去除污渍或污渍。也可使用玻璃纤维或尼龙抛光刷
习惯于2.在抛光过程中，使用80/20异丙醇/水溶液，尽量减少静电放电。3.打磨时不要过度用力。仅使用足够的力来照亮接触表面。检查边缘清洁后的连接器，以确保接触面无损失。4.用无绒布擦拭干净。检查连接注：执行此预防措施时，应关闭机柜电源维护任务。检查内部的所有信号接线、电源和接地连接
机柜以验证其完整性。检查连接时，务必转动螺钉、螺母或其他紧固装置
仅拧紧方向。如果连接松动，将收紧。如果连接紧固，紧固动作将验证它是否安全。决不能对其提出任何动议松开连接。1.验证机柜内的所有电源连接是否：保护2.验证终端装置的所有接线连接，或终端模块是安全的。警告机柜内有外露的交流和直流连接。这些暴露的电气连接存在电击危险这可能导致受伤或死亡。如果在电源输入面板断开系统电源后，输入或输出电路存在电击危险包含这些外部供电电路的机柜必须：带有警告标志，说明多个电源：
d swab to wipe the circuit board.2. Remove excess solvent by using compressed air to blow itfree of the circuit board.Edge Connector Cleaning1. Use a solvent mixture of 80% isopropyl alcohol (99.5%
electronic grade) and 20% distilled water.2. Soak a lint-free cloth with the solvent mixture.
3. Work the cloth back and forth parallel to the edge connector contacts.4. Repeat with a clean cloth that is soaked with the solventmixture.5. Dry the edge connector contact area by wiping with a cleanlint-free cloth.7 - 4 WBPEEUI240766B0Preventive Maintenance ProceduresTo clean tarnished or deeply stained edge connector contacts:1. Use a nonabrasive eraser or equivalent to remove tarnishor stains. Fiberglass or nylon burnishing brushes may also beused.
2. Minimize electrostatic discharge by using the 80/20 isopropyl alcohol/water solution during burnishing.3. Do not use excessive force while burnishing. Use only
enough force to shine the contact surface. Inspect the edge
connector after cleaning to assure no loss of contact surface.4. Wipe clean with a lint-free cloth.Checking ConnectionsNOTE: Power to the cabinet should be off while performing this preventivemaintenance task.
Check all signal wiring, power and ground connections within
the cabinet to verify their integrity. When checking connections, always turn a screw, nut or other fastening device in the
direction to tighten only. If the connection is loose, it will betightened. If the connection is tight, the tightening action will
verify that it is secure. There must not be any motion done toloosen the connection.1. Verify that all power connections withinthecabinet aresecure.2. Verify that all wiring connections to the termination unit,
or termination module are secure.WARNINGThere are exposed AC and DC connections inside the cabinet.These exposed electrical connections present a shock hazard
that can cause injury or death.If input or output circuits are a shock hazard after disconnecting system power at the power entry panel, then the door of the
cabinet containing these externally powered circuits must be
marked with a warning stating that multiple power sources
 

主营产品简介
专注于DCS、PLC、机器人控制系统、大型伺服四大系统领域。

主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。

优势：供应进口原装正品，专业停产配件，

发货快，货期精准，

主营品牌包括 ABB贝利、GE/FUANC、FOXBORO、英维思TRICONEX 、本特利BENTLY、A-B罗克韦尔、艾默生EMERSON 、OVATION、MOTOROLA、XYVOM、霍尼韦尔HONEYWELL 、力士乐REXROTH、KUKA、NI、DEIF、横河、伍德沃德WOODWARD、瑞恩、施耐德SCHNEIDER 、安川、 穆格MOOG、PROSOFT等品牌