CM-2 1044220190G 用于模拟量POS控制模块 DEIF 丹控

产品标题：CM-2 1044220190G 用于模拟量POS控制模块 DEIF 丹控

型号： CM-2 1044220190G 用于模拟量POS控制模块  

品牌  DEIF 丹控

质保：七天验收期，质保期一年
发货期：1-3个工作日

产品图片展示

产品详情资料
当通信接口要删除时，所有发送DSP必须
删除或重新定义。必须通过删除相应的
接收DSP，因为这些DSP不会更新。
CI522模块上配置的接收DSP无需移除
如果存在具有相同身份的其他接收DSP，则从任何其他站发送。如果没有其他站点
如果有接收DSP，则应将发送DSP从其站中删除，因为DSP将
淘汰的
不移除相关DSP的后果是其他通信
接口将CDP保留在扫描表中，并由此占用总线带宽，以避免使用。
由于发送CDP必须从配置CDP的电台中删除，因此CDP信号
除非整个总线重新启动，否则任何其他站点都不能使用该地址。另一个缺点
如果不删除其他站中的接收DSP，则在
发送DSP或其通信接口已被移除。
用另一个CI522通信接口替换通信接口，
参见第4.6.8节，交换单个CI522和第4.6.9节，交换冗余
CI522。
删除发送DSP后，请执行以下步骤以删除CI522
模块：
•重置CI522数据库元素上的IMPL终端。
•从CI522模块上拔下调制解调器电缆。
•卸下CI522模块。
其余通信接口将自动继续共享总线主设备
他们之间的责任，而忽视When the communication interface is to be permanently removed, all sending DSPs must be
deleted or redefined. All stations on the bus must be updated by deleting the corresponding
receiving DSPs as these will not be updated.
A receiving DSP, configured on the CI522 module to be removed, does not have to be removed
from any other station if there is other receiving DSPs with the same identity. If no other station
has a receiving DSP, the sending DSP should be deleted from its station as the DSP will be
obsolete.
The consequence of not removing the DSPs in question is that the other communication
interfaces will keep the CDPs in the scan tables and by this occupying bus bandwidth for no use.
As a sending CDP must be deleted from the station by which it is configured, the CDP signal
address can not be used by any other station unless the whole bus is restarted. Another drawback
of not removing receiving DSPs in other stations is that they will not be updated when the
sending DSP or its communication interface has been removed.
Replacing the communication interface with another CI522 communication interface,
see Section 4.6.8, Exchange of a single CI522 and Section 4.6.9, Exchange of a redundant
CI522.
When the sending DSPs have been deleted, perform the following steps in removing the CI522
module:
• Reset the IMPL terminal on the CI522 data base element.
• Remove the modem cable from the CI522 module.
• Remove the CI522 module.
The remaining communication interfaces will automatically continue to share the bus master
responsibilities between them and ignore the

主营产品简介
专注于DCS、PLC、机器人控制系统、大型伺服四大系统领域。

主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。

优势：供应进口原装正品，专业停产配件，

发货快，货期精准，

主营品牌包括 ABB贝利、GE/FUANC、FOXBORO、英维思TRICONEX 、本特利BENTLY、A-B罗克韦尔、艾默生EMERSON 、OVATION、MOTOROLA、XYVOM、霍尼韦尔HONEYWELL 、力士乐REXROTH、KUKA、NI、DEIF、横河、伍德沃德WOODWARD、瑞恩、施耐德SCHNEIDER 、安川、 穆格MOOG、PROSOFT等品牌