3BDH000002R1 AC800F基本单元自由现场控制器

产品标题：PM802F 3BDH000002R1 AC800F基本单元自由现场控制器 ABB

型号：PM802F 3BDH000002R1 AC800F基本单元自由现场控制器 ABB 

品牌： ABB

质保：七天验收期，质保期一年
发货期：1-3个工作日

产品图片展示

产品详情资料

在打开
包裹USG杜洛克™ EW2底漆包装在一个由两部分组成的预先测量套件中。两部分都必须
充分混合，不要混合部分材料。倒入B部分的全部内容物
放入A部分容器中。
使用带有Jiffy型搅拌器的电钻（300–400 rpm），将混合材料混合在
容器A放置两整分钟。不要用手混合。通过移动钻头混合所有材料
集装箱侧面和底部。重要事项-USG Durock的全部内容™ EW2底漆
必须在混合后立即从桶中倒出，否则材料可能会达到极限
温度和可能燃烧。
应用USG Durock™ EW2底漆，带刮刀和滚筒。搅拌后立即倒入
USG杜洛克™ EW2底漆以带状形式从混合容器中取出，并正确准备
混凝土基层。以大约175-200平方英尺/加仑（4.3-4.9平方米/升）的速度摊铺材料
（8-9密耳湿膜厚度），然后以1/4英寸的厚度进行反向滚动。（6 mm）绒毛酚醛芯辊。确保
均匀涂抹材料并消除胶泥，以防止多余底漆浮到表面
垫层的厚度。
立即广播分级、清洁、清洗、烘干的沙子。如果表面出现湿斑
撒砂后，未实现拒收；涂抹额外的沙子。
允许USG Durock™ EW2底漆开始固化（在77°F（25°C）下约30分钟）之前
应用USG Durock™ 或USG Levelrock底层。必须使用垫层
而USG Durock™ EW2底漆仍有粘性，且在底漆涂敷后4小时内。如果
4小时内未涂底漆，则必须在固化后重新涂底漆
足以继续行走。如果超过24小时，用机械研磨底漆并重新涂底漆。1
注1.养护时间和工作时间受环境空气温度和混凝土温度的影响。
应用USG Durock™ EW2底漆，带滚筒和刮刀。混合后立即倒入USG
杜洛克™ EW2底漆从搅拌容器以带状形式涂到适当制备的混凝土
基底以大约100-160平方英尺/加仑的速度摊铺材料。（2.5-3.9平方米
/五十） （16-18 mil.湿
薄膜厚度），然后以1/4英寸的厚度反向滚动。（6 mm）绒毛酚醛芯辊。立即广播
分级、清洁、洗涤、窑干砂完全拒收。如果之后表面出现湿斑
撒砂，未实现拒收；涂抹额外的沙子。允许USG Durock™ EW2型
底漆完全固化（在77°F（25°C）下约24小时）。如果存在任何裸露点
打磨裸露区域，彻底清洁，然后重新涂底漆和沙子，直至不合格。让底漆固化
（在77°F（25°C）下约24小时），并清除松散的沙子。Read the entire warning which appears on the last page of this submittal before opening the
package. USG Durock™ EW2 Primer is packaged in a two-part, premeasured kit. Both parts must
be mixed in full—do not mix partial amounts of the materials. Pour the entire contents of part B
into the part A container.
Using an electric drill (300–400 rpm) with a Jiffy-type mixer, mix the combined materials in
container A for two full minutes. Do not mix by hand. Mix all material by moving drill around
container’s sides and bottom. IMPORTANT - The entire contents of USG Durock™ EW2 Primer
must be poured out of the pail immediately after mixing or the material may reach extreme
temperatures and possibly combust.
Apply USG Durock™ EW2 Primer with a squeegee and roller. Immediately after mixing, pour
USG Durock™ EW2 Primer from the mixing container in a ribbon format to the properly prepared
concrete substrate. Spread material at an approximate rate of 175-200 sq. ft./gal (4.3-4.9 m²/L)
(8-9 mil. wet film thickness), then back roll with a 1/4 in. (6 mm) nap phenolic core roller. Ensure an
even coat of material and eliminate puddling to prevent excess primer from floating to the surface
of the underlayment.
Immediately broadcast graded, clean, washed, kiln-dried sand. If wet spots appear on the surface
after broadcasting sand, rejection has not been achieved; apply additional sand.
Allow USG Durock™ EW2 Primer to begin curing (approximately 30 minutes at 77 °F (25 °C)) prior
to application of USG Durock™ or USG Levelrock underlayments. Underlayment must be applied
while USG Durock™ EW2 Primer is still tacky and within 4 hours of the primer application. If the
underlayment is not applied within 4 hours, then you must reapply the primer after it is cured
enough to walk on. If more than 24 hours has elapsed, mechanically abrade the primer and re-prime.1
Note 1. Cure times and working times are influenced by both the ambient air temperature and the temperature of the concrete.
Apply USG Durock™ EW2 Primer with a roller and squeegee. Immediately after mixing, pour USG
Durock™ EW2 Primer from the mixing container in a ribbon format to the properly prepared concrete
substrate. Spread material at an approximate rate of 100-160 sq. ft./gal. (2.5-3.9 m2
/L) (16-18 mil. wet
film thickness), then back roll with a 1/4 in. (6 mm) nap phenolic core roller. Immediately broadcast
graded, clean, washed, kiln-dried sand to full rejection. If wet spots appear on the surface after
broadcasting sand, rejection has not been achieved; apply additional sand. Allow USG Durock™ EW2
Primer to fully cure (approximately 24 hours at 77 °F (25 °C)). If any bare spots exist, mechanically
abrade bare areas, clean thoroughly and reapply primer and sand to rejection. Allow primer to cure
(approximately 24 hours at 77 °F (25 °C)) and remove loose sand.
 
 

主营产品简介
专注于DCS、PLC、机器人控制系统、大型伺服四大系统领域。

主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。

优势：供应进口原装正品，专业停产配件，

发货快，货期精准，

主营品牌包括 ABB贝利、GE/FUANC、FOXBORO、英维思TRICONEX 、本特利BENTLY、A-B罗克韦尔、艾默生EMERSON 、OVATION、MOTOROLA、XYVOM、霍尼韦尔HONEYWELL 、力士乐REXROTH、KUKA、NI、DEIF、横河、伍德沃德WOODWARD、瑞恩、施耐德SCHNEIDER 、安川、 穆格MOOG、PROSOFT等品牌