07KT93 GJR5251300R0161 咨询使用数量

产品标题：ABB XV C767 AE102 3BHB007209R0102 咨询咨询 电源数字量控制卡

型号：ABB XV C767 AE102 3BHB007209R0102 咨询

品牌：ABB

质保：七天验收期，质保期一年
发货期：1-3个工作日

产品图片展示

产品详情资料

 a、 磁极编号
b、 偏离角度
c、 电杆类型
d、 停留次数
e、 跨度长度
f、 截面长度
g、 接地
h、 变压器编号。
i、 变压器容量
j、 所有类型电杆和设备汇总
施工工程师应确保按照要求更新竣工数据和图纸
制图和记录标准由承包商编制，并移交给相关方
电力部。
8八角钢杆
8.1钢杆类型
SEC标准钢电杆为锥形八角形，顶部热浸镀锌
盖、底座支承板、接地螺母、彩色标记、符合
SEC规范#20-SDMS-01的新版本。钢杆的标准长度为
中压单回路和双回路线路为12,13,14和15米，低压线路和短路线路为10米
杆式变压器（PMT）的H极结构。为了实现更高的目标
垂直间隙，也可以安装14和15米的钢杆。
只有在对没有撑杆或支柱选项时，才能使用自支撑杆
极钢杆类型详见下表5.1。
8.2搬运和运输
在装载、运输和卸载过程中应特别小心，以防止
电杆镀锌损坏。在以下情况下，电杆不得从车辆上掉落
在现场卸载，但应使用垫木或
用合适的带子或吊索吊离车辆。
不得安装任何损坏的电杆。
8.3孔
螺栓的孔间距取决于安装和管线配置。钻孔有
禁止。如果需要任何额外的孔，请参考配电工程
部门
9架空线路附件
架空线路附件应符合新版SEC规范的规定
编号20-SDMS-02。所有附件的安装数量应符合
施工图材料。
9.1螺栓
机器螺栓和带螺母和垫圈的肩部吊环螺栓应符合
线路附件SEC规范20-SDMS-02的新版本
 a. Pole Number
b. Angle of deviation
c. Pole Type
d. No. of stays
e. Span length
f. Section length
g. Earthing
h. Transformer No.
i. Transformer capacity
j. Summery of all type of poles & equipment
Construction Engineer shall ensure that updated as built data and drawings as required in
Mapping & Recording Standard are prepared by contractor and transferred to the concerned
Electricity Department.
8 OCTAGONAL STEEL POLES
8.1 Types of Steel Poles
SEC standard steel poles are tapered octagonal and hot dip galvanized complete with top
cap, base bearing plate, earthing nut, colour marking, pre-drilled holes conforming to the
latest revision of SEC specification # 20-SDMS-01. Standard lengths of steel poles are
12,13,14 and 15 m for MV single and double circuit lines and 10 m for L.V lines & the short
pole of H-pole structures of pole mounted transformers (PMT). For achieving higher
vertical clearances, 14 and 15m steel poles can also be installed.
Self support poles shall be used only when there is absolutely no option for stay or strut
pole. Types of steel poles are detailed below in Table 5.1. 
8.2 Handling And Transportation
 Special care shall be taken during loading, hauling and unloading to prevent any
 damage to the galvanizing of the poles. Poles shall not be dropped off vehicles when
 being unloaded in the field, but shall be carefully rolled, one at a time, with skids or
 lifted off the vehicle with suitable straps or slings.
 Any damaged pole shall not be installed.
8.3 Holes
Holes spacing for bolts is based on installations and lines configurations. Holes drilling are
prohibited. If any additional hole is required, refer to the Distribution Engineering
Department.
9 OVERHEAD LINE ACCESSORIES
The overhead line accessories shall be as specified in the latest revision of SEC specification
No. 20-SDMS-02. All accessories shall be installed in quantity as specified in the list of
material of the construction drawings.
9.1 Bolts
Machine bolts and shoulder eye bolts with nuts and washers shall be as specified in the
latest revision of SEC Specification No. 20-SDMS-02 for line accessorie

主营产品简介
专注于DCS、PLC、机器人控制系统、大型伺服四大系统领域。

主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。

优势：供应进口原装正品，专业停产配件，

发货快，货期精准，

主营品牌包括 ABB贝利、GE/FUANC、FOXBORO、英维思TRICONEX 、本特利BENTLY、A-B罗克韦尔、艾默生EMERSON 、OVATION、MOTOROLA、XYVOM、霍尼韦尔HONEYWELL 、力士乐REXROTH、KUKA、NI、DEIF、横河、伍德沃德WOODWARD、瑞恩、施耐德SCHNEIDER 、安川、 穆格MOOG、PROSOFT等品牌