SCHUMACHER ATCS-15 1464-0320自动化控制模块

产品标题：SCHUMACHER ATCS-15 1464-0320F
产品型号：SCHUMACHER ATCS-15 1464-0320
品牌：SCHROFF
发货期：1-3个工作日，具体可联系客服
质保：质保期一年！

产品图片展示

产品详情资料

2） 更改针数时，使用开关更改针数，并设置过程A到C的针数。要更改整个过程的次数，用开关改变它，并设置过程D的数量。（可以改变的针数A、B和C的范围：0到19针。可以改变的过程D的范围：0-9次）3）踩下踏板前部一次，缝纫机将重复正常缝纫和反向缝纫，重复次数为规定次数。然后，缝纫机将自动启动剪线器并停止，以完成重叠缝合过程。（一次自动缝纫不能关闭。）4）当选择剪线禁止功能时，重叠缝纫程序完成后，机器将停止，机针向上，不进行剪线。4.方形缝合图案按下可显示图案列表屏幕。1） 按下开关选择方形缝合图案，屏幕自动切换到方形缝合设置屏幕的针数，显示已经设置的针数。OFF ON OFF ON缝纫图案OFF OFF ON ON–12–2）更改反向缝合的针数时，请使用开关进行更改，并设置A和B的针数。此外，更改方形缝合的针数时，用开关改变它，并设置C和D的针数。（可以改变的针数范围：A和B=0到19针，C和D=0到99针）3）按下开关，在缝纫开始时设置倒缝。4） 按下开关可设置缝制结束时的倒缝。5） 缝纫机在完成过程C和D的过程后自动停止。此时，当按下触摸开关（补偿缝纫操作）时，缝纫机会低速旋转。此外，当踏板返回空档位置并且再次踩下其前部时，无论针数设置如何，都可以继续缝纫。6） 当选择自动剪线开关时，剪线在后一个过程完成后自动执行。（当设定了缝制结束时的倒送缝纫时，缝制结束后的倒送缝合成为后一道工序，该工序完成后自动剪线。）7）当选择剪线禁止开关时，缝纫机将停止，针向上，不进行剪线。8） 当选择一触式自动缝纫开关时，通过踩下C和D工序的踏板前部，以设定的速度不间断地执行自动缝制。9）当缝纫机配备自动升降器时，在C和D过程完成后，压脚自动上升。无设置倒缝在开始缝制时在开始缝纫时双倒缝无设置倒缝制在缝制结束时在结束缝制时双倒缝制-13-在信息模式中，您可以指定、检查和编辑各种数据，也可以执行其他操作。信息模式由操作员级和维护人员级组成。有关操作员级别，请参阅IP-100E/SC-510的说明手册。[维护人员级别]1）打开电源。2） 按下开关3秒钟以调用信息屏幕。■ 信息屏幕（维护人员级别）1）按下相应的开关以显示相应功能的屏幕。（按开关、或3秒钟进行相应操作。）按开关结束信息模式，屏幕返回到信息模式之前的状态。版本显示…………..1.参考版本功能。缝制常用设置…………..2.参考缝制常用数据功能。功能设置…………..请参阅IP-100E/SC-510说明手册。缝制管理设置……3.请参阅缝制管理信息。数据通信…………..4.参考通信功能。SM格式（智能媒体）…………..5.参考SM格式功能。（注意）执行智能媒体格式时，当前记录的所有数据都将消失。请注意，除了智能媒体的初始化之外，不要将格式用于任何其他目的。（6） IP-100E信息模式–14–1）版本功能此功能允许您查看每个组件的版本，例如操作面板[IP-100E]、IPOP板[SC-510扩展]和CTL板[SC-50主体]。■ 版本显示屏[标准设置2) When changing the number of stitches, change it with switches and for setting the number of stitches for processes A through C. To change the number of times of the whole processes, change it with switches and for setting the number of processes D. (The range of the number of stitches A,B and C that can be changed : 0 to 19 stitches. The range of the number of processes D that can be changed : 0 to 9 times) 3) Depress the front part of the pedal once, and the sewing machine will repeat the normal stitching and reverse stitching as many as the number of specified times. Then the sewing machine will automatically make the thread trimmer actuate and will stop to complete the overlapped stitching procedure. (The one-shot automatic stitching cannot be turned OFF.) 4) When thread trimming prohibiting function is selected, the machine will stop with the needle up upon completion of the overlapped stitching procedure without performing thread trimming. 4. Square stitching pattern Press to display the pattern list screen. 1) Press switch to select the square stitching pattern, and the screen is automatically changed over to the number of stitches of square stitching setting screen to display the number of stitches which has been already set. OFF ON OFF ON Sewing pattern OFF OFF ON ON – 12 – 2) When changing the number of stitches of reverse stitching, change it with switches and for setting the number of stitches of A and B. In addition, when changing the number of stitches of square stitching, change it with switches and for setting the number of stitches of C and D. (The range of the number of stitches that can be changed : A and B = 0 to 19 stitches, C and D = 0 to 99 stitches) 3) Press switch to set the reverse stitching at the start of sewing. 4) Press switch to set the reverse stitching at the end of sewing. 5) The sewing machine automatically stops after completion of the process at processes C and D. At this time, the sewing machine rotates at low speed when the touch-back switch is pressed (compensation stitching operation). In addition, when the pedal is returned to the neutral position and the front part of it is depressed again, the sewing can be continued regardless of the setting of the number of stitches. 6) When automatic thread trimming switch is selected, thread trimming is automatically performed after completion of the last process. (When the reverse feed stitching at the end of sewing is set, the reverse feed stitching at the end of sewing becomes the last process, and automatic thread trimming is performed after completion of the process.) 7) When thread trimming prohibiting switch is selected, the sewing machine will stop with the needle up without performing thread trimming. 8) When one-shot automatic stitching switch is selected, automatic sewing is performed at the set speed without a break by depressing the front part of pedal at processes C and D. 9) When the sewing machine is provided with auto-lifter, the presser foot automatically goes up after completion of the process at processes C and D. No setting Reverse stitching Double reverse stitching at the start of sewing at the start of sewing No setting Reverse stitching Double reverse stitching at the end of sewing at the end of sewing – 13 – In the information mode, you can specify, check, and edit various data and also perform other operations. The information mode consists of the operator level and maintenance personnel level. Refer to the instruction manual of IP-100E/SC-510 for the operator level. [Maintenance personnel level] 1) Turn ON the power. 2) Press the switch for 3 seconds to call the information screen. ■ Information screen (Maintenance personnel level) 1) Press the respective switches to display the screens of the respective functions. (Press the switch , , , or for 3 seconds for corresponding operation.) Press switch to end the information mode, and the screen returns to that before the information mode. Version display ..............................1. Refer to the version function. Sewing common setting ................2. Refer to the sewing common data function. Function setting .............................Refer to the instruction manual for IP-100E/SC-510. Sewing management setting .........3. Refer to the sewing management information. Data communication......................4. Refer to the communication function. SM format (Smart media) ..............5. Refer to the SM format function. (Caution) When the smart media format is executed, all data which have been currently recorded will disappear. Be careful not to use the format for any other than the initialization of the smart media. (6) IP-100E information mode – 14 – 1) Version function This function allows you to view the version of each component such as operation panel [IP-100E], IPOP board [SC-510 expansion], and CTL board [SC-510 main body]. ■ Version display screen [Standard setting

主营产品简介
专注于DCS、PLC、机器人控制系统、大型伺服四大系统领域。

主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。

优势：供应进口原装正品，专业停产配件，

发货快，货期精准，

主营品牌包括 ABB贝利、GE/FUANC、FOXBORO、英维思TRICONEX 、本特利BENTLY、A-B罗克韦尔、艾默生EMERSON 、OVATION、MOTOROLA、XYVOM、霍尼韦尔HONEYWELL 、力士乐REXROTH、KUKA、NI、DEIF、横河、伍德沃德WOODWARD、瑞恩、施耐德SCHNEIDER 、安川、 穆格MOOG、PROSOFT等品牌。

只卖库存产品;出完需订货!价格以客服说明为准!!订货货期以客服说明为准，有任何疑问请联繁客服! Limited stock, Contact US!

●使用前:

在操作和维护，安装设备之前，请阅读并严格遵守安全相关的信息。

Read and strictly follow safety-related information before operatingmaintainingand installing equipment.

●使用者要求:

必须从事安装，组装或维护设备等相关工控电气机械以及其他相关技术的人员。

Must be engaged in the installation,assembly or maintenance of equipment and other related industriacontroeectrica machinery and other related technica personne.应用范围:

应用于品牌本系列工业以及生产生活自动化设备产品。

Used in the brand of this series of industriaand production automation eauipment products

适用于场景:系统集成，非标定制，产线升级改造，原设备电气替换等等。

Suitable for scenarios:system integration,non-standard customizationproduction line upgrading and transformation,electrical replacement of original equipment,etc.

●操作人员:

应该由本品牌专业培训操作员来安装、操作和维修设备。专业人员具有技术能力强，熟悉安全信息和安全实施:

熟悉设备的安装加工、操作和维护:熟悉处理所有的潜在危险情况。

Equipment should be installed,operated and maintained by trained operators from the brand

●危险情况

警告

.请注意使用人员的人身安全。

●除了产品特性以及功能，还需了解产品的使用寿命环境。

●充分学习产品使用手册，否则非专业人员可能会造成人身危险。

Study the product instruction manual thoroughlyotherwise it may cause personal danger to non-professionals.

●服务行业

适用水泥，木业，石业，橡胶，石油，化工，发电，环保，水处理，制冷，交通，钢铁，食品，饮料，船舶，制冷等行业

Applicable to cementwood,stone,rubber,petroleumchemical, power generation,