GE IC670MDL241咨询通用电气

产品标题：GE IC670MDL241
产品型号：GE IC670MDL241
品牌：GE  
发货期：1-3个工作日，具体可联系客服
质保：质保期一年！

产品图片展示

产品详情资料
n概述本文件介绍与安全控制站（SCS）一起使用的ALR111和ALR121型串行通信模块，用于执行Modbus通信。通过使用SCS的Modbus从机通信功能，Modbus主机可以设置或引用SCS中的数据，该主机是通过串行通信模块与SCS分离的系统。此外，可以使用SCS的子系统通信功能，通过串行通信模块设置或引用来自定序器的子系统数据。这些串行通信模块可以安装在SSC60上, 50不锈钢, SSC57型, 和SSC10 通过ESB总线与安全控制单元连接的安全控制单元和SNB10D安全节点单元。F01E。ai子系统调制解调器子系统调制解调器SCS串行通信电缆串行通信模块串行通信电缆串口通信电缆串行通讯电缆（Modbus主机）其他系统图串行通信模块的配置示例2保留所有权利。版权所有©2012，横河电机公司>>GS 32Q06K50-31E n硬件规格ALR111和ALR121串行通信模块的硬件规格如下所示。这些模块是无干扰模块，对安全回路没有干扰。表串行通信模块硬件规格项目规格型号ALR111 ALR121接口RS-232C RS-422/RS-485（4线制）连接方法点对点（RS-422）多点（RS485）通信功能半双工同步方法启停同步传输速度1200/2400/4800/9600/19200/38400 bps传输码二进制字符长度8位（Modbus从机通信功能和子系统通信功能上固定为8位）停止位长度1/2位（子系统通信函数上固定为1位）奇偶校验数据传输后无/偶/奇滞后时间1毫秒传输距离大15米大1200米（总扩展长度）安装方法安装在SSC60上, 50不锈钢, SSC57型, SSC10系列, 或SNB10D（*1）I/O接线AKB131、AKB132、AKB135、AKB136电缆等。带3对屏蔽的电缆，AKB161或AKB162接线连接D-sub-9针（内螺纹×2端口），用接线板的M4螺钉夹紧（5极×2口）通信功能（*2）Modbus从机通信功能，子系统通信功能电流消耗0.5 A 0.5 A重量约0.3 kg约0.34 kg*1:SNB10D与SSC60连接, 50不锈钢, SSC57型, 或SSC10 通过ESB总线*2： SCS的一个单元能够处理多种通信功能：但是，不同类型的通信功能不能在串行通信模块上同时执行。这意味着两个端口必须具有相同的通信功能。n操作环境l硬件要求串行通信模块在以下SCS上运行。SSC60S、SSC60D、SSC50S、SSC50D、SSC57S、SSC57D、SSC10S和SSC10D l软件要求串行通信模块在以下SCS上的控制功能上运行。CFS1300安全控制功能包（用于SSC60 和Vnet/IP）：用于SSC60 CFS1100安全控制功能包：用于SSC50/SSC10系列 CFS1170安全控制功能包：（用于SSC57 和Vnet/IP上游）：用于SSC57 l工程要求可使用CHS5100安全系统生成和维护功能包执行工程工作。2015年11月27日-00>>3保留所有权利。版权所有©2012横河电机公司GS 32Q06K50-31E n安装环境CFS1300安全控制功能包（用于SSC60 和Vnet/IP）要安装的通信模块数量（*1）多2个单元/SCS（*2）（用于Modbus从站通信功能）多4个单元/SSC（*3）（用于子系统通信功能）*1：由于Modbus从属通信功能和子系统通信功能模块可以安装在同一SCS上，通信模块的大数量为6个单元/SCC*2： 这是ALR111、ALR121和ALE111的总和。*3：这是ALR111和ALR121的总和。CFS1100安全控制功能待安装通信模块的包装编号（*1）多2个单元/SCS（*2）（用于Modbus从站通信功能）多4个单元/SSC（*3）（用于子系统通信功能）*1：由于Modbus从属通信功能和子系统通信功能模块可以安装在同一SCS上，通信模块的大数量为6个单元/SCC*2： 这是ALR111、ALR121和ALE111的总和。*3：这是ALR111和ALR121的总和。CFS1170安全控制功能包（用于SSC57 和Vnet/IP上游）要安装的通信模块数量（*1）多2个单元/SCS（*2）（用于Modbus从机通信功能）多4个单元/SSC（*3）（用于子系统通信功能）*1:Modbus从属通信功能和子系统通信功能模块可以安装在同一SCS上，并且通信的大数量n GENERAL This document describes about Models ALR111 and ALR121 Serial Communication Modules used with a safety control station (SCS) for performing Modbus communication. By using the SCS’s Modbus slave communication function, the data in SCS can be set or referred to by the Modbus master which is as separate system from SCS via a serial communication module. Furthermore, the subsystem data such as from sequencers can be set or referred to via a serial communication module using SCS’s subsystem communication function. These serial communication modules can be mounted on SSC60, SSC50, SSC57, and SSC10 safety control units and SNB10D safety node unit that are connected with safety control units by ESB bus. F01E.ai Subsystem Modem Subsystem Modem SCS Serial communication cable Serial communication module Serial communication cable Serial communication cable Serial communication cable (Modbus master) Other system Figure A sample configuration of the serial communication modules 2 All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation > > GS 32Q06K50-31E n HARDWARE SPECIFICATIONS Hardware specifications of ALR111 and ALR121 serial communication modules are as shown below. These modules are interference-free modules that have no interference with the safety loop. Table Serial Communication Module Hardware Specifications Item Specifications Model ALR111 ALR121 Interface RS-232C RS-422/RS-485 (4-wire system) Connection method Point-to-point Point-to-point (RS-422) Multipoint (RS-485) Communication function Half-duplex Synchronization method Start-stop synchronization Transmission speed 1200/2400/4800/9600/19200/38400 bps Transmission code binary Character length 8 bits (Fixed to 8 bit on the Modbus slave communication function and the subsystem communication function) Stop bit length 1/2 bits (Fixed to 1 bit on the subsystem communication function) Parity check None/even/odd Lag time after data transmission 1 ms Transmission distance Maximum 15 m Maximum 1200 m (total extended length) Installation method Mounted on SSC60, SSC50, SSC57, SSC10, or SNB10D (*1) I/O wiring AKB131, AKB132, AKB135, AKB136 cables, etc. Cable with 3-pair shield, AKB161, or AKB162 Wiring connection D-sub-9-pin (female × 2 ports) Clamped with terminal block’s M4 screws (5 poles × 2 ports) Communication function (*2) Modbus slave communication function, subsystem communication function Current consumption 0.5 A 0.5 A Weight Approx. 0.3 kg Approx. 0.34 kg *1: SNB10D connects with SSC60, SSC50, SSC57, or SSC10 by ESB bus. *2: A unit of SCS is capable of handling multiple communication functions: however, different types of communication functions cannot be simultaneously performed on a serial communication module. It means that two ports must have identical communication functions. n OPERATING ENVIRONMENT l Hardware Requirements The serial communication module runs on the following SCS. SSC60S, SSC60D, SSC50S, SSC50D, SSC57S, SSC57D, SSC10S, SSC10D l Software Requirements The serial communication module runs on the control functions on the following SCS. CFS1300 Safety Control Functions Package (for SSC60 and Vnet/IP): for SSC60 CFS1100 Safety Control Functions Package: for SSC50/SSC10 CFS1170 Safety Control Functions Package: (for SSC57 and Vnet/IP-Upstream): for SSC57 l Engineering Requirements Engineering work can be performed with CHS5100 Safety System Generation and Maintenance Function Package. Nov. 27, 2015-00 > > 3 All Rights Reserved. Copyright © 2012, Yokogawa Electric Corporation GS 32Q06K50-31E n INSTALLATION ENVIRONMENT CFS1300 Safety Control Functions Package (for SSC60 and Vnet/IP) No. of communication modules to be mounted (*1) Max. 2 units/SCS (*2) (for Modbus slave communication function) Max. 4 units/SCS (*3) (for subsystem communication function) *1: Since Modbus slave communication function and Subsystem communication function modules can be mounted on the same SCS, the maximum number of communication modules is 6 units/SCS. *2: This is the sum of ALR111, ALR121, and ALE111. *3: This is the sum of ALR111 and ALR121. CFS1100 Safety Control Functions Package No. of communication modules to be mounted (*1) Max. 2 units/SCS (*2) (for Modbus slave communication function) Max. 4 units/SCS (*3) (for subsystem communication function) *1: Since Modbus slave communication function and Subsystem communication function modules can be mounted on the same SCS, the maximum number of communication modules is 6 units/SCS. *2: This is the sum of ALR111, ALR121, and ALE111. *3: This is the sum of ALR111 and ALR121. CFS1170 Safety Control Function Package (for SSC57 and Vnet/IP-Upstream) No. of communication modules to be mounted (*1) Max. 2 units/SCS (*2) (for Modbus slave communication function) Max. 4 units/SCS (*3) (for subsystem communication function) *1: Modbus slave communication function and Subsystem communication function modules can be mounted on the same SCS, and the maximum number of communication modules is 6 units/SCS. *2: This is the sum of ALR111, ALR121, and ALE111. *3: This is the sum of ALR111 and ALR12 

主营产品简介
专注于DCS、PLC、机器人控制系统、大型伺服四大系统领域。

主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。

优势：供应进口原装正品，专业停产配件，

发货快，货期精准，

主营品牌包括 ABB贝利、GE/FUANC、FOXBORO、英维思TRICONEX 、本特利BENTLY、A-B罗克韦尔、艾默生EMERSON 、OVATION、MOTOROLA、XYVOM、霍尼韦尔HONEYWELL 、力士乐REXROTH、KUKA、NI、DEIF、横河、伍德沃德WOODWARD、瑞恩、施耐德SCHNEIDER 、安川、 穆格MOOG、PROSOFT等品牌。

只卖库存产品;出完需订货!价格以客服说明为准!!订货货期以客服说明为准，有任何疑问请联繁客服! Limited stock, Contact US!

●使用前:

在操作和维护，安装设备之前，请阅读并严格遵守安全相关的信息。

Read and strictly follow safety-related information before operatingmaintainingand installing equipment.

●使用者要求:

必须从事安装，组装或维护设备等相关工控电气机械以及其他相关技术的人员。

Must be engaged in the installation,assembly or maintenance of equipment and other related industriacontroeectrica machinery and other related technica personne.应用范围:

应用于品牌本系列工业以及生产生活自动化设备产品。

Used in the brand of this series of industriaand production automation eauipment products

适用于场景:系统集成，非标定制，产线升级改造，原设备电气替换等等。

Suitable for scenarios:system integration,non-standard customizationproduction line upgrading and transformation,electrical replacement of original equipment,etc.

●操作人员:

应该由本品牌专业培训操作员来安装、操作和维修设备。专业人员具有技术能力强，熟悉安全信息和安全实施:

熟悉设备的安装加工、操作和维护:熟悉处理所有的潜在危险情况。

Equipment should be installed,operated and maintained by trained operators from the brand

●危险情况

警告

.请注意使用人员的人身安全。

●除了产品特性以及功能，还需了解产品的使用寿命环境。

●充分学习产品使用手册，否则非专业人员可能会造成人身危险。

Study the product instruction manual thoroughlyotherwise it may cause personal danger to non-professionals.

●服务行业

适用水泥，木业，石业，橡胶，石油，化工，发电，环保，水处理，制冷，交通，钢铁，食品，饮料，船舶，制冷等行业

Applicable to cementwood,stone,rubber,petroleumchemical, power generation,